Moving gpio pin in device tree leads to error

[ErwinCes]

Hello,

in my device tree there are three nodes/items concerning battery Management:

1. One load enable pin
2. One measure enable pin
3. the required ADC configuration

The following configuration works:

	batloaden {
		compatible = "gpio-keys";
		bat_load_en: bat_load {
			gpios = <&gpio1 12 GPIO_PUSH_PULL>;
			label = "batLoadEnPin";
		};
	};
	
	btmeasen {
		compatible = "gpio-keys";
		bt_meas_en: bt_meas {
			gpios = <&gpio1 14 GPIO_PUSH_PULL>;
			label = "btMeasEn";
		};
	};
	batmeasure {
		bat_adc_conf: bat_adc_conf {
			compatible = "bat-adc-config";
			resolution = <12>;
			gain = <6>;                  //Numeric value of ADC_GAIN_1
			stabilize_time = <3>;
		};
    }

The pin configuration is taken in my Code via

static const struct gpio_dt_spec BatMeasENpinspec = GPIO_DT_SPEC_GET(BAT_MEAS_EN_PIN_NODE, gpios);

But when I try to Group the whole measurement stuff into one node as

	batmeasure {
		bat_adc_conf: bat_adc_conf {
			compatible = "bat-adc-config";
			resolution = <12>;
			gain = <6>;                  //Numeric value of ADC_GAIN_1
			reference = <4>;             //Numeric value of ADC_REF_INTERNAL
			aquisition_time = <0x4028>;  //Numeric value of ADC_ACQ_TIME(ADC_ACQ_TIME_MICROSECONDS, 40)
			ucal_channel_id = <0>;
			ubat_channel_id = <1>;
			ucal_plus_input = <1>;             //Numeric value of NRF_SAADC_INPUT_AIN0
			ucal_minus_ubat_plus_input = <2>;  //Numeric value of NRF_SAADC_INPUT_AIN1
			ubat_minus_input = <3>;            //Numeric value of NRF_SAADC_INPUT_AIN2
			stabilize_time = <3>;
		};
		bat_load_en: bat_load {
			compatible = "gpio-keys";
			gpios = <&gpio1 12 GPIO_PUSH_PULL>;
			label = "batLoadEnPin";
		};
		bt_meas_en: bt_meas {
			compatible = "gpio-keys";
			gpios = <&gpio1 14 GPIO_PUSH_PULL>;
			label = "btMeasEn";
		};
	};

I get the error identifier "__device_dts_ord_DT_N_S_batmeasure_S_bt_meas_P_gpios_IDX_0_PH_ORD" is undefined for the line static const struct gpio_dt_spec BatMeasENpinspec = GPIO_DT_SPEC_GET(BAT_MEAS_EN_PIN_NODE, gpios);

Practically I just moved the pin node from top into my matmeasure node.

The pin node is queried by

#define BAT_MEAS_EN_PIN_NODE    DT_NODELABEL(bt_meas_en)

which seems to work in both cases.

Is it required that all my gpio defines are at the top Level to get the Right __device_dts… define?

Regards

Erwin

[Simon]

I think the reason GPIO_DT_SPEC_GET is failing in the second approach is because you're adding the "gpio-keys" compatible to the same node as the gpio-keys properties. The correct approach is to add the properties under a child node of the "gpio-keys" node.

If you look at the yaml bindings file of "gpio-keys" you can see that "properties" is added under "child-binding". Read more about child-binding in the documentation: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.1.0/zephyr/build/dts/bindings.html#child-binding 

	parent {
		compatible = "gpio-keys";
		//don't add properties here
		child {
			//add properties here
		};
	};

Best regards,

Simon

[ErwinCes]

Great! It works now.

Just one Question to improve my understanding. I can Change it in two ways:

even before my adc conf
batmeasure {
		compatible = "gpio-keys";
		bat_adc_conf: bat_adc_conf {
			compatible = "bat-adc-config";
			resolution = <12>;
		};
		bat_load_en: bat_load {
			gpios = <&gpio1 12 GPIO_PUSH_PULL>;
		};
		bt_meas_en: bt_meas {
			gpios = <&gpio1 14 GPIO_PUSH_PULL>;
		};
	};
	
or behind my adc_conf to cover only the gpios	
batmeasure {
		bat_adc_conf: bat_adc_conf {
			compatible = "bat-adc-config";
			resolution = <12>;
		};
		compatible = "gpio-keys";
		bat_load_en: bat_load {
			gpios = <&gpio1 12 GPIO_PUSH_PULL>;
		};
		bt_meas_en: bt_meas {
			gpios = <&gpio1 14 GPIO_PUSH_PULL>;
		};
	};	

Both ways seem to work; at least it compiles and does the stuff it should be.

In the documentation I haven't found anything About order. Would in both my ways bat:adc_conf also be compatible with gpio-keys? Or never as I have a dedicated compatible Statement in the bat_adc_conf node? Or not when I put the gpio-keys compatible line only after bat_adc_conf (but before the first pin=

[Simon]

ErwinCes said:

In the documentation I haven't found anything About order.

I don't have any documentation to back this up, but I don't think the order of where you put the gpio-keys compatible statement matters. 

ErwinCes said:

Would in both my ways bat:adc_conf also be compatible with gpio-keys?

That is a good question. I'm not sure what happens when a child node of a gpio-keys node have it's own compatible. Would you be able to test it? Do you get any complaints that the required gpios property is missing from bat_adc_conf? 

Wouldn't it be better to organize it like this?

batmeasure{    
    bat_adc_conf: bat_adc_conf {
		compatible = "bat-adc-config";
		resolution = <12>;
	};

    batmeasure_gpios {
    	compatible = "gpio-keys";
    	bat_load_en: bat_load {
    		gpios = <&gpio1 12 GPIO_PUSH_PULL>;
    	};
    	bt_meas_en: bt_meas {
    		gpios = <&gpio1 14 GPIO_PUSH_PULL>;
    	};
    };
};

Best regards,

Simon

[ErwinCes]

Hi Simon,

you wrote "I'm not sure what happens when a child node of a gpio-keys node have it's own compatible. Would you be able to test it?". As I wrote before, I used it and it worked. This is my first described way:

The gpio compatible statement was before my adc conf node and the gpio nodes after my conf node. I saw nothing, that doesn't work. 

So practically in that case I have a child compatible statement in my parent together with an own compatible statement in my node. Can it be that a compatible statement in my node kicks out all child compatible statements in my paremt? Or can a node have two compatible statements in practice: one own and one child statement from my parent? But in that case I could have even more compatible statements: if my parent still has a parent with a child statement, there might be three statements valid for me.

As written, this is somehow an academic question, as each solution works. But to complete my understanding of all this device tree stuff I would like to have an answer what is possible.

Your proposal, to move the gpios into a dedicated node below my batmeasurement is also a good idea and I guess it would work also.

Best regards

Erwin

[Simon]

I have forwarded your questions internally. I'll keep you updated.

Best regards,

Simon