Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
I am looking at this example: github.com/.../main.c
In ble_evt_dispatch (line 315), this function forwards an BLE event to all of the modules. By looking at ble_evt_t,...
I am trying to build a BLE central application on the mbed compiler (target BLE Nano).
I have chosen the ble_app_uart_c example from the nRF5 SDK as a starting point. My...
Hi Support Team,
one error come out when use nrf connect, just as attached picture shows,
please help to check what cause this error,
no error come out on phone.
...
In reference to this issue in the Android DFU library...
github.com/.../33
... can someone from Nordic please explain how DFU OTA using the secure format on a device...
Hi,
I working on nRF52 series development boards communication. I am using ESB library for data transfer. I am able to transfer the data between two microcontrollers. Now...
My device is connected with GSM module, when GSM module communication fail, I need to save the error message to flash. In application level, pstorage_store or pstorage_update...
Hi,
I use fstorage fun in nRF5_SDK_12.1.0_0d23e2a.
and the same code can run SDK11 but It seems different now.
So how to use fstorage fun in SDK12 and I list the different...
I was looking for something like a checklist of what to do when developing on a custom board but I couldn't find it.
I am working with Keil 5.15.
I achieved to develop...
Hello, i have a question.
Can nRF51822(s120) handle more than one connection at same time?
Let me explain: i have one server(nRF51), and two(or more) clients(nRF51 and mobile...
My Chip is a Insight SIP ISP1302.
It's based on a 51822_xxAB, 128kb Flash and 16kb RAM.
I try to use the S130 with the UART Application.
The S130 2.0.1 requiers 108kb...
Hi,
NRF_LOG_PRINTF() is working fine with peripheral examples in SDK11. but when I try to do the same in ble_peripheral examples it is not working. I have defined the following...
Hi. I have one question:
From SDK and docs, I can find how many pipes and which pipe nRF24LU1 open when it is TX.
I check function:
void hal_nrf_open_pipe(hal_nrf_address_t...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
