Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I have migrated application with freertos (S132 /NRF52 devkit ) from SDK 11.00 to SDK12.00 .
Flashed SD 3.00 and then application ,but Application is not able to boot...
Hi,
Is this the right way of reading the timer value using the capture task. In this code i am trying to read the updated value of counter for every event generated in...
Hello;
I'm developing an application that advertises as a connectable peripheral. As such, it has an ID (think of it like a beacon minor).
I have 2000 of these devices...
Does bootloader example dfu_dual_bank_ble_s132_pca10040 from SDK v11 work with softdevice v3.0?
when I try to run the dfu_dual_bank_ble example with softdevice 3.0, I got...
Hi ,
I have 2 nrf51 dongle compiled with a code which can scan and advertise ibeacon constantly. Whenever receive advertisement packet from each other , they are able to...
Hello,
I'm running one advertiser and one scanner at the same time, and I want to change the data inside the advertise packet, every advertise. Looking at the forum and...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi all, Now I'm working secure bootloader in sdk12 for these I installed the nrfutilv1.5.0 by following nrfutil user guide
link text
while I'm creating .zip files it...
I've seen similar questions posted, but none that match my situation exactly and those solutions did not work for me.
I'm using the pca10040 dev kit, which I connected...
For the radio peripheral, if I use a shorts (shortcut) from END to DISABLED states, is EVENT_END still set? Because I enable an interrupt on EVENT_END, but not on EVENT_DISABLED...
Does anyone know how to remove all Nordic software and clean out all registry keys?
Installed mastercontrolpanel.3.9.0.6.x64.msi and all is working great with the RF Dongle...
Hello together,
i have a question to the uart hardware communication.
I try to send 6 bytes from the nRF51 DK, S130, SDK12 (p0.09 tx) pin to another hardware rx pin.
...
Hi,
Trying to add DFU service on the new SDK, but when compiling getting this:
compiling nrf_dfu_flash.c...
..\..\..\..\..\..\components\libraries\bootloader\dfu\nrf_dfu_flash...
I'm using SDKv12 S132v3 on nRF52 peripheral device. I have characteristic with following security setup:
char_add_params.read_access=SEC_JUST_WORKS;
char_add_params.write_access...
