Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
We are implementing a device where we need to use BLE and PWM. For generating PWM we use app_pwm library. To decide on the number of cycles of PWM pulses, we use a separate...
Hi,
Is there a way to power only the nrf52832 on the development kit(PCA10040)?
Background: We would like to test a solar power source but we don't want to power the...
Thank you very much in advance for any help.
I am attempting to upload an example firmware on a nRF52832 with the s132 softdevice BLE stack and the example DFU bootloader...
just like
github.com/.../nrf52-mpu-easydma-using-timers-and-drivers
we add a sensor, and try to read 2 sensors by 3 command in i2c.
is it possible to still using ppi...
Hi Friends,
I am beginner for nRF51822 and I install uVision 5.20 to create program for this chip.I can't see this chip on device selection table when new project creating...
Hi,
I've recently bricked my nrF51822 Beacon Kit ( www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit)
...by uploading some bad firmware. I can no longer program...
I am beginner for nRF51822.I installed uVision 5.20 to program nRF51822 chip.I could not see nRF51822 chip on chip selection guide of uVision software.Also I need some example...
Hello.
I've been trying to use the nRF Beacon for Eddystone app to configure a nRF52 devkit. The idea is to configure a slot as EID and register it to my google account...
Hi there,
I know 3V lithium batteries (Lithium Manganese Dioxide) batteries would be perfect for the nRF51822, but we're wondering if Lithium Thionyl Chloride (Li-SOCl2...
Hello,
is there a softdevice for the nRF52 which supports the proprietary wireless protocoll of the radio nRF24L01+? I only find ones which supports Bluetooth 4.0 and ANT...
Hello,
i have a very small device with bluetooth connection which send data every 20ms to a smartphone. The adc is sampling 100 times per second. Because of the small design...
Morning
I was just wondering if anyone knows which types of Bluetooth devices work with the nRF Toolbox for iOS and where to buy them - proximity etc.
Iain
Dear Nordic Engineers!
I am using the nRF51422 QFACA1 on custom boards and planning to migrate from SDK8.0.0 to SDK11.0.0
My application is using the S120 soft device...
Hi all! I want to send data from a beacon (nrf51822) to a Pic microcontroller with the RS232 standard, what function should I use to send data? I have already tried but it...
hello.
I want use I2C program.
so, I used twi_master_using_app_twi example.
SDA is output only 1byte(0x21).
I need to output a continuous 5byte.
Where do I need to modify...
