Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
hello:
I open nrf51-ble-tutorial-service-master\SDK 11.0.0\nrf5-ble-tutorial-service\pca10040\s132\arm5_no_packs\ nrf52-ble-tutorial-service.uvprojx, and compile ,the result...
Hello,
I am developing custom driver for TWIM. I am facing a problem with DNACK and ANACK which hangs my application. SCL and SDA lines are monitored through Saleale logic...
hello,
again, sorry for the begginers qustion(probablly i will have 2-3(hopefully) in the next few days). I got today the nrf52-dk, and on the back of the nrf52 is written...
I ask the questition yesterday ,maybe i have not expressed clearly.In my project , I have to use three spi in master mode and three twi in master mode to communicate with...
Hi!
In my teamwork we are developing an application for use a sensor module via spi, and share data and comunicate with other devices via Bluetooth.
I've taken care...
Dears,
We are working for a dongle solution to exchange data.
Have any BLE SDK solution via Uart to exchange data between host & client? and that the host is no need...
Hi,
I am using nRF51822xxaa and s130 and SDK 10.0. nRF51 connects with the app(notifications enabled), then bonds with it. Subsequent communications between the app and the...
I connected with RTT Viewer 5.12f with nrf51 DK board.
while I donwload firmware to the board, I got bunch of error message from RTT viewer..and it stop..sometime the download...
I am having two issues with the following code:
When I run this sample code on my NRF52DK (there's external hardware connceted but that does not affect this operation...
Hello, everyone~
I used to see nRF51802 in an official document but cannot find it in the official website. Is there an nRF51802? If so, what are the differences between...
Hello Everyone,
Can anyone give me recommendation of a BLE App for Eddystone TLM (with temperature)?
Till now, I used the Beacon Manager. But I think the App has a problem...
The gpio specifications table lists 3mA for VDD greater than 1.7V and 6mA for voltages greater than 2.7V but what about in between?
Would a linear approximation between...
Hello,
I am trying to fix the UART communication error in a peripheral side.
First of all, the setup that I am using is as below.
[SDK] nRF5_SDK_11.0.0_89a8197
...
We would like to enable the flash protection for an nRF52 application with the typical scenario:
to disable flash reads from the JTAG,SWD interface; only erase/reprogram...
Hello everyone.Recently I try to send some information from a "nrf51822" to phone when they are connected .So I choose "ble_app_hrs" example program,and I add two characteristics...
