Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I have bought a Tayio Yuden EYSGJNZWY Bluetooth module, which is in fact just a Nordic's nRF51822 (256KB Flash and 32KB RAM) with added antenna. Tayio's files say that the...
Hi,
I have built an application which is based on BLE and protocol that supports high frequency sampling of sent messages. I tried to achive that using only BLE, but it...
Hello,
I am designing a custom board with NRF52832 IC. I have a query regarding routing of traces.
In my design, I am not using all pins of IC. Do I need to route traces...
Hello,
I am designing a custom board with NRF52832 IC. I followed the same layout design as suggested by Nordic.
But , I made some additions to reference layout. I added...
I'm trying to set up a gazell device with a channel table that is 16 channels long. This is for a pairing application where the host has a channel table that is 6 channels...
I'm using SDK13.0.0 ble_app_ancs_c example.
On connected with a phone, pm_evt_handler is called with PM_EVT_CONN_SEC_SUCCEEDED, and call ble_db_discovery_start(), then...
hi,
i want to make BLE central node with Nrf52840 for receiving multiple data from Nordic thingy 52,i am using keil IDE with Nordic sdk 14.2.0 and blinkey central(s140_PCA10056...
Is this possible to change MTU Size in nrf51822 Board from 23 to 43?
is any changes is done android side app? the application is same copy of nrf Toolbox UART app.
please...
Hi, everyone,
I am developing the project on nRF518522 and I must use the flash memory to save the data. The data must be saved while the device is conncted via BT with...
hi,
When using the UART examples I found that as long as I opened the uart_init () program will not work, debug the discovery process will be executed
case APP_UART_COMMUNICATION_ERROR...
Hi,
I am trying to develop an application which recieves data over SPI and I want to send this data over ble, I am using NUS service. I am recieving 5 bytes over SPI at...
Hello,
I'm using 2 nRF58840 dev kit with SDK 14.2.0.
I'm trying to read the RSSI value of the second board from the first board using LE Coded PHY in both modules.
...
Hi every body , i have some issue if you don't mind. i rooted a board with NRF52832 SOC without PCA. i want to get a uart connection with pin 8 and 10 . It s possible to do...
Hi,
I am wondering if its possible to download a fds record on android device when connected ?
I want to save data and retrieve it when I get connected to it.
Th...
