Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Hi,
I am currently conducting measurements using channel sounding with my nRF54L15 boards. I am at the end of my master thesis, so there is not so much time left to really...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hi,
I have two nRF5340 DKs and want one to be server, one be client. I use NCS offcial code and simply buide them, however, " LED3 starts blinking green on every device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi everyone,
In nRF9160 with ncs 2.9.0 I've problems when trying publish a MQTT payload bigger than 2700 bytes aproximately. In advanced I already was adequated buffer size...
Based on 'ble_app_template' in nRF5_SDK_12.2.0 (S132), I develop a program with nRF52832.
The problem is that the program will restart after reaching APP_ADV_TIMEOUT_IN_SECONDS...
Hi,
I have a few questions about using floating point in nRF5 chips. As discussed here , nRF51 has no FPU but we can simply use "float" in Keil and have the operations...
My device as a slave, if the surrounding environment is not good, the unknown master device connected to my slave device caused the real master device to be unable to scan...
Dear Nordic family,
I tried programming MDBT40 (purchased from Raytac ) with the same code which worked with nRF51822 Bluetooth Low Energy BLE 4 and 2.4GHz Wireless Communication...
I'm trying to implement a simple RTC timer into my project, and it seems like the app_timer module is the best way to do that, especially when using the Softdevice. I added...
Hello,
we are facing the following issue when using Android and trying to rebond with a previously bonded S110 peripheral:
Bonding the Android device with the S110 based...
We are looking to store a unique name and number in each device as it is provisioned from the factory, and are considering using the UICR. We are using something close to...
when i use the ble_adverting_start(BLE_ADV_MODE_FAST) it return error code : 8 it is from then APP_ERROR_CHECK(err_code) it can system abnormal. the error is from sd_ble_gap_adv_start...
I use PCA 10040 as a Central, and PCA 10028 as a peripheral. I want the central to connect and pair and bond with the peripheral.
I use S130 for PCA10028, s132 for PCA10040...
I have an application which uses the S132 softdevice and communicates with a DAC over I2C. The twi is in non-blocking mode. Furthermore, there is a significant delay between...
Hi All,
I'm busy exploring the ble_peripheral_uart example and ran into a couple of issues I don't fully understand. Upon flashing the S140 SoftDevice and application program...
Hello All
I am using Soft device 130 and SDK version 12.2.0 ..i am planing to make SPI camera Interface .
I referring SDK online document..there is no any API for slave...
Hello,
Is there any way to disable the "Enhanced Power Control" feature of the BLE standard? I am working with nRF51-DK in the connection mode and I need fixed transmit...
