I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello,
I'm trying to enable the monitor debug mode work with iar but I have some doubts about the address used in the EnableMonMode.mac macro provided in one of the blog...
Hi all,
I'm using nRF Sniffer (2.0.0-1.beta), i didn't have any problem for follow connection between master and slave but now, I have a problem with time displayed in...
Hi,
I need to use the radio timeslot api in my application. I'm using nrf52 ,SDK 14.0.0 and softdevice version 5.0.0 . I've gone through the tutorial for setting up timeslot...
Hello,
I'm testing PHY coding (for long range), I'm pretty surprise from what I get when I scan the RSSI of bluetooth channels (with Nordic app).
This is my set up:...
i want to erase and store the flash after detecting the radio active.
The radio signal is also active, when i erase and store .
Do erase and store the flash may influence...
Hi there,
I try to using nrf sniffer for trouble shooting, and follow the "nrf sniffer user's guide v2.0" , when I copy the unzip extcap's content to the Wireshar's Extcap...
Hi!
i am thinking about cut off uart when data is not transmitting.
As a method 1, i am thinking about using CTS and RTS Pin which is hardware flow control!
①Is this possible...
I'm using the nRF52 DK with mbed, running the heart rate monitor demo app.
When I disconnect the board from the PC and attach a USB power supply instead, the nRF52 won...
Hey all,
I'm working with the nRF51822 (nRF51dk) on a mac running high sierra, and I've been following this tutorial to try to get started. But when I try to make flash...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
