I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
I am using an nRF52DK kit, SDK V11.0.0 and SoftDevice S132 V2.0.0. I have found an advertising example on the site github.com/.../nrf51-ble-tutorial-advertising . I have modified...
Hi,
We made a custom PCB using the NRF52832. We have connected a button to P0.21 which is the reset pin. We have configured this button as input and set the preprocessor...
Hi,
I am using multiperipheral configuration. I want a characteristic to be read by only a specific peer among connected peers. How do i recognize and authorize this specific...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all!
I´m trying to use FDS to read and write to my nRF51 using the example from Infocenter.
The write seems to be OK and returns 0x00.
But fds_record_find() returns...
Hi everyone.
I want to add RFX2411N to extend BLE signal coverage. I also need to minimize power consumption. I used VDD_PA to control TXEN and 2 gpios control both TXEN...
Hi,
I am testing the USB CDC ACM Secure DFU Bootloader example via NRF52840.
softdeivce uses 5.0.0-2 alpha and uses SDK version 14.1.
I have a problem.
I ran Erase...
Hi,
I need to activate one pin just before the sample is taken on a saadc channel. I have settings as in saadc example.
How can I do this? Is there any event that I...
Is it possible to send more than 255 bytes on SPI when nrf52832 is used as slave. A few solutions use SPI Master with easyDMA and ArrayList to do this. Will the same solution...
Hello,
I have a question is it possible to break the nrf52832 if I try to load the application when the UART of the module is active(TX and RX pins are 1).
The softdevice...
Context :
I am using a nrf52832 to communicate via UART to a STM32 on a custom board. I've based my work on the Ble nus service example.
Main change from the DK is that...
I am playing with example app from this tutorial devzone.nordicsemi.com/.../
I can see the app only when I start debugging. If I just power up my custom board, it doesn...
nRF52, S132, SDK13.
I need flash two .hex files. One- firmware, second- data. It flashed on a factory. data- veans serial number and other personal chips info. Now I can...
We want to flash ble_peripheral over nrf52. How can we proceed?
we use the code from following link when we try compile this code in segger studio we get following errors...
I am using keil 5, softdevice 132, sdk NRF_SD_BLE_API_VERSION=5, nRF52832.
I am trying to work with firmware update over ble.
In the example folder, there is an example...
