Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I have recently got a n5 start kit nRF51422. I went through all the set up procedures in the user guide, installed all the correct programs/drivers etc.. My unit...
Hello.
I am looking at the schematic of the nRF51422 USB dongle development kit. The pin P0.30 of the microcontroller is attached to ground. As the pin could potentially...
I'm writing a PC utility in Visual Studio to connect to BLE devices. I'm using the PCA10000 and MasterEmulator.dll. I'm able to discover the services and characteristics of...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all,
I am using the multi role example ( github.com/.../nRF51-multi-role-conn-observer-advertiser) to scan and advertise concurrently.
I was wondering if the scanning...
I have a 16MHz external clock oscillator to drive a micro controller in my system. Can this also be connected to the crystal input on the nRF24L01+ to drive it's clock? Should...
Hi All,
I wanted to write a patient record to glucode measurement charateristics from android Phone which supportes BLE features . How do i write a record to BLE device...
When using the OTA DFU using the button press implementation is it possible for the bootloader to require bonding? I figure I can use the preserve app data functionality built...
Just took the developer.mbed.org/.../ code and run it on the board.
But when I try to connect with my phone I get: "Device doesn't support UART. Disconnecting".
What...
Hello,
I am using the RedBearLab's BLE Shield 2.0 and I'm trying to modify the advertisement data using nRFgo studio to include manufacture data (type: xFF) for one of...
