I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
When I change ATT_MTU size and add the following code:
#define CONN_CFG_TAG 1
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg));
ble_cfg.conn_cfg...
How do you do
Now use the Nordic nor51822 \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart this routine plus
Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples...
Hello,
Am working on NRF52 interface via SPI to Micron N25Q flash .
Am able to identify flash by reading chip identification correctly and after this to test memory writing...
We are a small R&D team and we are currently developing a medical wearable. We are using nrf52832 and we are generating approximately 54kbps (6.75kBps). I 'd like to ask if...
Hi!
After reading few posts about spi slave/master issues... I'm also challenging with one of them. I have following setup nrf51822, s130 2.0.1 and sdk 12.3.0… nrf51 (spi...
I am working on OTA DFU about nRF52810.
My refernece project are ble_app_uart\pca10040\s132 and bootloader_secure_ble\pca10040
I find that the RAM start address between...
Hello im trying to create a single master connected to multiple slave to make synchronous movement for my robotic arm project but im not entirely sure which Bluetooth to consider...
Hi,
I am running the BLE DFU example. I am able to perform the DFU OTA implementation successfully. The problem I am facing is that, once the application has been updated...
Hi everyone,
I am developing a remote control using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello,
I used translation software.
I am measuring current.
I want to enable dc-dc mode.
how to enable the dc-dc?
also,where should I change the source code?
I...
Hello folks, we are currently using RedBear Lab Arduino toolchain to develop a MDBT40 based application. However we meet a lot issues on merging bootloader.hex (downloaded...
Hi,
Since I'm having a hard time understanding this through the SDK docs, I'll ask it here.
I'm currently using a BMD200 module (from Rigado) which uses a nRF5188.
...
I have a BLE-Nano v1.5 board with 32KB of ram starting at address 0x20000000 (til 0x20008000). However when I want to read a byte of the uper 16K (0x2004000+), I get a 'cannot...
I need to scan for nearby beacons.
This was featured in the mbed examples but does not seem to be described anywhere else
I am using SDK12 at the moment.
I found the...
hello
Now I use the nRF52832's board and I was measuring the current
But when the board's power is off and i measured, the current was flowed in the board.
Now i am using...
