Hi, I have created my own hardware with nRF54L15 – 2xLED, 2xPWM, and Radio (BLE). I am trying to create a custom board using the graphical wizard. LED and PWM seems to work...
I have an external GPS module connected to an nrf9151dk over UART. The module is correctly powered, and sending messages over its tx pin, which has been confirmed by attaching...
I´m trying to change the installation path of the Nordic Power Profiler as I´m running out of space.
I have about 9GB left, but when trying to open a captured file, Power...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
Hello,
I would like to measure the current consumption of my nRF9161 and compare the result with a standard measurement. While searching in your documentation, I found this...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hi,
I have a board with a real time clock IC which is kept alive during power downs. I want the Nordic nrf52840 to read the time from the real time clock and then use this...
Hi,
I have an application where first nrf51 would be the central (remote control) and the second nrf51 would be the peripheral. I got the peripheral to bond with the nRFConnect...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
This is related to another post seen here:
devzone.nordicsemi.com/.../
Basically, I took the peripheral UART example and modified it so all UART printing was disabled...
Hi,
I am using
*nRF52840, SDK13.1, SD140, TWIM, easyDMA enabled. I have tried with the both 0 and 1 instance.
Looking in DSO, I am pretty sure that, after nRF is sending...
I edit the Tx power in ble_app_beacon application (0dbm and 4dbm) using this function and i observing the rssi values in nrfconnect app in mobile.i didn't find the differences...
I've compiled a new app with a new BLE service and module to go along with it (for different work than my other question, I can test this service in a generic LE explorer...
Hi All,
There should be a typo in " nRF24LE1_Product_Specification_rev1_6", page 82, Figure 35.
The Unprotected Program memory is shown 10 kB, but seems it should be 12...
Hi All,
I'm new to nrf51822. I'm developing a battery powered device using the Nordic ble_app_uart_s110_pca10028 peripheral example program. I'm glad to inform you my core...
i want to change the conn_params .
the first gap_params_init() ,
as below: gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//20ms gap_conn_params.max_conn_interval...
hi everyone,
I've downloaded s140 and trying to run BLE notification example. I'm able to see state changes in the advertising on putty terminal at COM 7, but when I try...
Hi. i'm using nRF52832.
As datasheet says, flash endurance min value = 10,000.
Isn't there max value?
There is no limited life cycle for flash?
I just wnat to estimate...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
We bought 3 nRF52-DKs (based on nRF52832 and PCA10040 V1.2.1). We compiled, built, and flashed the systems with several provided examples from nRF5_SDK_14.1.0_1dda907...
Hi,
I am working on a project where I have 4 sensors. Each sensor transmits(slave & Peripheral) its value using BLE to the Receiver (Central & master) which is also BLE...
I need to create a service on the nRF52832 that can send large amounts of a few different data types to the central device. For instance
ADC1 sampling (~256 bytes/s...
