Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Seems battery reads are not consistent in thngy52 2.1.0 software.
Observed a ~4% difference in the consequent battery reads. This difference is high (upto ~40%) if the thingy...
In the recent past, I used a SoC in which GPIOs could be configured as "open drain", that is in which there is an internal transistor where the SOURCE is grounded, the DRAIN...
Hey,
I'm using nRF as a SPI slave with a Raspberry Pi. I'm seeing that even at ~3MHz SPI frequency, my first byte transferred gets corrupted. I have a test setup where...
I am using nrf52 with s132 and armgcc
As I add functionality to the code I get to a stage where it fails. Linker runs OK but the result fails to execute.
The observable...
I am currently working on a BLE beacon project on nRF51822. Using SDK 12.3.0 and s130. The device has to advertise URL, advertising name and output power level. And these...
I am trying to control a current measurement chip (DDC114) that works with a protocol that is close (enough) to SPI. It has 2 channels, s.t. it can be read out and integrating...
I am attempting to run my first bit of code on my Nordic nRF52-DK and every time I have attempted to upload the code to the board, the board disconnects in the middle of the...
Hi, I'm using nRF52832, SDK13.0.0 as peripheral.
My iPhone app(my company's) makes connection without problem.
But Android app gets connection fail when it tries to connect...
Hi @ all,
We tried to enable debug log for lwIP module by setting NRF_LWIP_DRIVER_CONFIG_LOG_ENABLED in sdk_config.h to 1.
This threw two errors during the build process...
Hi @ all,
by working on a MQTT project using IoT SDK v1.0.0 (SDK v14.1) we discovered problems with TCP packets not being transmitted.
Using lwIP, transmitting TCP packets...
Hi there,
I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
Hi.
I'm testing multiperipheral function,
and have established multiple connections (1 single Peripheral with multiple Centrals).
But it seems that the Peripheral can...
I have no idea what is going on.
I am using IAR 7.8 and as I wrote, it gets reset when it hit the breakpoint.
every variable return to its initial value, and BLE get disconnected...
Hello,
I was wondering whether or not the standard analog pins on the nrf52832 have to be defined as analog inputs with the gpio methods.
I ask this because I am trying...
Hi there, I was able to work with uart ble example described in tutorials/36/.
My question is how to disable encryption on BLE link? Specifically, we need to make disable...
