Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Should these beacons be advertising as bought off-the-shelf? I've got six and was expecting to be able to pick up their advertisements but I'm getting nothing.
In this application, I tried to enter a wrong bonding passkey to test PM_EVT_CONN_SEC_FAILED case. But I found that the program went into this case and after executed "sd_ble_gap_disconnect...
We developed a new BLE hardware product using the Laird BL652 third party module. Our product is based on the latest Softdevice S132 V5.0.0.
Now I'm starting the Bluetooth...
I have problems getting the beacon example in the new mesh SDK v0.10.0 working.
I invoke cmake with this command:
cmake -DTOOLCHAIN=gccarmemb -DPLATFORM=nrf51422_xxAC...
Hi there~. This is Matthew! I saw a thread explaining that the production variants of the nRF52840 will first be available Q4 2017 at this link .
I was planning for BLE...
Hi,
I had a difficult problem.
First, S110 & SDK9
ble_stack_init () is the source.
static void ble_stack_init(void)
{
uint32_t err_code;
// Initialize the...
Hi. I'm using nRF51822 as Peripheral.
To init the service for example "NUS", i have to call NUS_BASE_UUID as below..
#define NUS_BASE_UUID {{0x9E, 0xCA, 0xDC, 0x24, 0x0E...
Hey guys,
From what I understand, the minimum connection interval on say, an iPhone, is 20ms. Also, you can send up to 6 packets of 20 bytes within a connection interval...
I have established a ble connection between two dk boards, the code I based on is the ble_app_uart_c and ble_app_uart, and try to detect some rising edge delivered from the...
It's kind of relative question with my previous question.
"When smartphone range is shorter than a peripheral(nRF5X), is there any way to receive an advertisement from the...
Hi all, I tested the example: Experimental: LE Secure Connections Multirole Example with my smartphone and it is working fine, but when I tried use LESC on my peripheral device...
I can't open a com port after starting the nRF Connect app. This happens in Windows (native) and also a Linux virtual host with the com port passed through. I'm using a nRF51...
I found strange behavior when using back-to-back packet transmission.
Configuration of PTX/PRX is:
No Auto-ACK (disabled)
CRC 2 bytes
Packet length 13 bytes
Addr...
I have the blinky examples working, but have not been able to get any example code using any gpio input to work. they compile fine but the buttons done seem to work. I'm using...
