I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I've got a little confused about variety of peer/bonding/whitelist abstractions realized in NRF5 SDK. My goal is to maintain longterm connections (nrf52832 peripheral + smartphone...
I use two nrf51 chips, one of which works as central and second one as peripheral. After the DM_EVT_LINK_SECURED event is generated on the peripheral side I'm starting the...
Is there a way to advertize without having to advertize advertisment flags?
The problem is because of these flags I only have 26 bytes left instead of full 29 bytes. It...
Hi,
I want to add custom characteristic to NRF THINGY:52.
I am getting BLE_ERROR_INVALID_ATTR_HANDLE while I update the value to the characteristic.
Update is done...
Hi, I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using the latest version of SES and a J-Link Plus. SDK version 14.1.
I've modifed the CLI...
Hi Support Team,
I am trying to create the custom model - as far as I know there are two types of models possible in bluetooth 5 mesh - SIG defined and vendor specific...
Hello,
I have been playing with sdk 14.0 examples for a while and I wanted to try the Nordic UART ble_app_uart using multiple files (ble init, advertising, sdh separate...
I am writing a combined beacon and mesh node using the mesh SDK v0.10.
When dsm_local_unicast_addresses_set() is called in mesh_evt_handler() , which can be found in nrf_mesh_node_config...
I've sifted through the examples given to me, and none of them seem to explain how to create your own service and add it to the stack. All of the services that are registered...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
