Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi everyone,
I am using board PCA10040 v1.1.0, softdevice 13.0.0, Eclipse Oxygen. I am trying to scan my phone and communicate with it but the scaned UUID is increasing...
Suppose I configure RTC0 and RTC1 to have the same LFXO clock source (with a 30uSec tick) and start them in quick succession. Will their counters read the same value?
I...
I just started trying to get an IOT IPv6 application up and running. On the nrf51882 end, I have flashed the IPv6 COAP server. The LED on the device is happily flashing away...
Hi,
It looks like system (laptop windows 7) is not supporting more than two windows of RTT viewer simultaneously.
When I connect, third one, it disconnects, one of the...
Hi
The concept of setting the event_length (the time set aside per connection) was introduced post softdevice v3.0.0. To my understanding, with softdevice v3.0.0, the softdevice...
I have a android phone, and it says there's a FW update (1.1.0) for the thingy (it says I'm on 0.0.0). I confirm that I want it, but nothing happens. What can I try? I get...
We are using a nRF52840 (QIAAAA) on a custom board which replicates exactly the schematic used by the development kit (PCA10056). When using Segger RTT for debugging purposes...
I am using adv_report_parse to try and return the device names the scanner picks up. However device names are being printed repeatedly.
I have 4 to 5 devices around me...
Hi
The serial connection handler "ser_conn_handlers.c" may case an INVALID_LENGTH error when receiving Advertise Reports (or other long BLE events). The reason for this...
I have BLE Nitrogen. It is defined as a disk on which it can be dropped hex and it is loaded. Please explain in detail how to make hex which can be dropped on the device....
I have code running on a nRF52 device, with SoftDevice enabled, based on the example given in this topic:
devzone.nordicsemi.com/.../
This runs fine on its own, and...
Hello !
I am currently working on a custom board on which I don't need 32.768kHz. I want to use P0_1 as an interruption pin connected to a pushbutton. The button is connected...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52840 PCA10056,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
Hey .My source code was compiled against SDK 8.0 now we need to upgrade the SDK to 10.0.
I have just copied the SDK10.0.0"components" folder to my project ( replaced the...
