Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi, I have problem with using printf() in SEGGER RTT.
I've read tutorial and others about SEGGER RTT printf() problem, but they didn't work.
When I use printf() in RTT...
hi,
I found ble_app_multilink_central example under SDK but this is for LED button application.
Is it possible to configure the same example for NUS?
I worrying about...
I have app (based on buttonless_dfu) works on sdk 13, sd 3, nrf52832.
Now I try to migrate this app to newest SDK14, sd 5.
I can't resolve one issue. I have main.c and 7...
hi, I found ble_app_multilink_central example under SDK ,and make it work with NUS. Some problems bothered me.
When the amount of data reaches a certain amount, the transfer...
Hi,
Tried this getting started tutorial:
github.com/.../Nordic_SDK_User_Guide.md
When building project at the end, I get: (After trying max optimization)
linking...
Hi,
I am trying to program a custom board with ISP1507 chip from dynastream based on nRF52832 using the nRF52 DK. I have connected P20 on the DK to the chip as follows...
Hello, myCode: https://goo.gl/ggTei4 & Photo : https://goo.gl/Sq28tC
Please Help me with Dynamic NRF24L01 Mesh network
I have connected nodes via DHCP 01, 02 upto 05 to...
Hello everyone!
Do have any different between Read/Write internal flash with softdevice and non softdevice!
And how can I get example Read/Write internal flash with softdevice...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
