How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
We found a problem with a client's legacy design. They use two 12 pF load capacitors for the 32 MHz crystal, which has a 4 pF capacitance. This is a somewhat unusual Abracon...
Hello DevZone,
I have a project where I currently use the AT%XPOFWARN feature, in order to turn off the modem in case the battery voltage is too low. It's used in both cellular...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
Dear Nordic DevZone,
I'm encountering pairing issues with mobile devices and a nRF54 DevKit flashed with HCI over UART firmware. After initial pairing, deleting the bonding...
Hi,
I am trying to send sensor(accelerometer) data through beacon. I am basing my logic on the beacon example. I am putting my sensor data into an array and passing it...
Hi,
I have an nRF51 DK, found here www.nordicsemi.com/.../nRF51-DK .
I am using SDK V11.0 and S130 V2.0.
I am developing on a Linux machine.
I can compile and run...
Hi.
I'm using the Power Profiler Kit and the PPK desktop application to log the power consumption of my device. This works well for short time spans.
However, I'd also...
Hi
I'm trying to delete all files with a given file id. Will fds_file_delete() delete all files with a given file id, or just the first one it finds?
thanks
SDK1...
Hi
I'm trying to use fds_record_find() to detect if a record exists in flash storage. After erasing the device (via nrfjprog), flashing the softdevice, flashing the program...
I use an app_timer to periodically update sensor reading in my application. There is a characteristic used to change updating rate by stopping and restarting the app_timer...
Hi,
I work on a project for the nRF52832 with Keil µVision using ARM Compiler V5.06 update 2 and nRF5 SDK 11.
In a module I allocate quite some memory using malloc(...
For the BLE GAP advertising flags byte in the advertising data, we have the following options:
/**@defgroup BLE_GAP_ADV_FLAGS GAP Advertisement Flags
* @{ */
#define...
I cannot seem to save the new Device Name value in the nRF51822 beacon.
I am using the mobile app nRF Connect.
This is my procedure:
1).Run nRF Connect on Android device...
Hi Nordic Team;
I am using nrf51822 devices with sdk12.3.0. I am using buttonless dfu example without any problem with sdk12.3. However, I see that you realese sdk14 that...
We're considering nRF51/52 to implement a specific BLE application. We need the nRF51/52 go to sleep if a BLE collision signal or interference on an advertising channel has...
Hi,
I'm using nRF5_SDK_13.0 on nRF52840 based on ble_app_hrs_rscs_relay example. I use it to connect a bluetooth 4.0 device and it's ok now. Also I have a bluetooth 5.0...
Hello, our device is able to be used by Iphone and Andriod. For the ANCS, we have tested the Iphone and it is OK. However, Andriod notification does not need the ANCS. As...
Hi
I'm trying to create a custom ble service with 4 notify characteristics.
Everything works with one characteristic, but when i add the other the DK hangs.
I'm using...
According to the NRF52810 datasheet，to ensure optimal performance it is essential that you follow the schematics- and layout references closely.Then if I want to use NRF52810...
