Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
If I want to get 16kHz output sample rate of PDM,then what should I do? How to cofigure the register PDMCLKCTRL and the clock HFCLK? Could you give me more details? An example...
Here are 4 broadcast signal, the first is send with dfu, whenever how I try, it only display 8 characters in max.
And the second and the fourth named begin with "LOCK_...
Hi,
I have a question about my schematic.
In the datasheet I've read that it doesn't matter which pin is used for several pheripherals like SPI.
So does this means...
Hello,
I am using 12 bit ADC in my application but data element more than 8bit is not send correctly, Also not receiving Array[10000] element. I am using nrf52.
Thank...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi,
Let's assume that we know there is a packet ready to be sent every 20ms. Now what is the best connection interval from power consumption point of view? Here is my understanding...
I've been unsuccessfully attempting to download and execute a BLE example on a nRF52832, and I could not succeeded probably due to false alignment of Soft device's and application...
I'm running the ble_my_project_template example from ble-sdk-arduino , and listening to the ACI lines with a logic analyzer. Here is what I found in the first transmission...
Gentle folks,
I'm sure I'm making some simple, primitive error. Please help me mend my ways :-)
Using gcc in the NetBeans IDE on MacOS for building and running the ble_app_hrs...
Hi,
I tried to flash the mbed FOTA bootloader on my nRF51 DK. I copied the bin file to the bootloader device. It said the storage on the device is to small. Now it won...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I am working on NRF52 custom board with 3.7mA 27mAH battery, working on BLE app UART example SDK11 with SoftdeviceS132V2.0.
I made BLE advertise for 20 sec interval...
I prototyped a nRF52832, WLCSP package, with a fab (PCBA) and put jumpers between my 32Mhz crystal and the chip, attempting to connect with a j-link in SWA mode, I cannot...
Hi. I'm using nrf52832.
Now I'm using HFXO, LFXO to operate BLE. As I know I should use HFXO to operate BLE.
What about LFXO? Can I use internal clock(LFRC RC osc) instead...
