After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello
i am using the nrf52840 with sdk 13.
on the client side i saw you are catching the cccd_handle. for the heart rate characteristic.
basically i am leaning the basic...
Hi all, is it possible to use NRF51-DK for Master Control Panel?
I dont have NRF51 dongle so I was thinking if there is a way to make NRF51-DK work with MCP.
Hi,
I have the following situation:
1 central connects and bonds to 2 peripherals. All the above 3 devices are power cycled.
Now, the central need to remember the...
My system's data rate is 16MHz.it input to nRF52832 is parallel 8 bits. Is it possible? I want input the data to RAM by easyDMA,please to tell me how to do it ? thanks!
Hello,
A stupid newbie question: APP_UART_FIFO_INIT seems to get stuck while trying to run
example code.
Only modification I have made is the usage of SEGGER_RTT for...
I am working in sdk14 nrf52832 ble_app_hids_keyboard_pca10040_s132.
I set the .allow_repairing flag to true :
static void pm_evt_handler(pm_evt_t
const * p_evt) {...
My system's extend IC need a 16MHz clock ,because the nRF52832 work in 64MHz,so I want to use nRF52832 to generating a 16MHz clock output to a GPIO pin .please tell me ,how...
Hi,
I'm using nRF52832 and nRF52840 to work with MCU, then we should do the firmware update by the uart. I have compiled the bootloader_secure_serial project in the SDK...
I have ordered two "nRF51822 Bluetooth Smart Beacon Kit"s on this page:
www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit , and got these two:
I've downloaded...
Am building a HID Mouse device, starting with the nRF52-DK as hardware target and the BLE peripheral HID mouse sample app. Builds, loads and runs, apparently fine (i.e., can...
Hello,
I am trying to add an extra service like "experimental_ble_app_blinky" into "ble_app_hids_keyboard" example code. "ble_app_hids_keyboard" example code has 3 servcies...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
i am using uart of nrf52832. the SDK is nRF5_SDK_12.3.0_d7731ad. the uart is app_uart .when i was testing the uart sending and receing .i find that the uart is stoping where...
Hello!
We are performing certification testing for our product. We have nRF52832 chip on the board. We used "radio test" example to perform the test and almost all worked...
