Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
Hi there,
I've already downloaded ble_mesh_v0.9.1-Alpha SDK and I can use arm-none-eabi-gcc to compile it, one thing I want to know is that how can I switch HWID to 52 in...
Hello,
I'm trying to use ble_app_hrs_rscs_relay_pca10056_s140 on a nRF52840 Preview DK using example from SDK 13.0.0_04a0bfd.
When I copy the precompiled .hex file in...
Hi,
I'm trying to add another element with a simple onoff model to control a second LED on the same server node.
I get APP_ERROR. I try declaring m_server0, m_server1, generic_get0_cb...
Hello,
I want to use at the nRF52832 a temperature sensor TMP108 and an EEPROM via TWI bus which are connected to Pin 5 (SDA) and Pin 6 (SCL). I made a lot of time until...
Hello,
I have a custom board with a Taiyo Yuden chip (it integrates an nRF51822 QFAC chip, 2 crystals and the BLE antenna).
I program it using SWD. I succesfully uploaded...
Hi,
I'm trying to use nRF52832 by external oscillator(ash7k-32.768KGZ-T).
When i use SDK13, i just add clock setting like below.
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_Xtal...
Hello,
I'm using the SDK 14 and the FDS library.
I'm a bit confused about one thing :
FDS uses Flash Storage to write to flash.
Since SDK14 Flash Storage can work...
Working with: examples/ble_peripheral/ble_app_uart . I would like to change on_ble_evt priority level so that UART IRQ handler has lower priority then softdevice event dispatching...
Hi! I'm using openthread with custom-made board with NRF52840. During development of lowpower thread application I found out one big problem which i couldn't resolve. I've...
Hello i am now implementing a nordic52832 project On this
nRF5_SDK_14.0.0_3bcc1f7\examples\proprietary_rf\esb_ptx
nRF5_SDK_14.0.0_3bcc1f7\examples\proprietary_rf\esb_prx...
Hi,
I am currently implementing an application which uses PPI to control SPI transaction when a HIGH-LOW transition is detected on a GPIO pin.
I first set up the transaction...
The *_DEF macros in SDK14 define service structures as static. This means that the application level functions for a service must all be called from the same c file where...
