Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I'm using the nRF52 DK with mbed, running the heart rate monitor demo app.
When I disconnect the board from the PC and attach a USB power supply instead, the nRF52 won...
Hey all,
I'm working with the nRF51822 (nRF51dk) on a mac running high sierra, and I've been following this tutorial to try to get started. But when I try to make flash...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
Is there a nordic guide which lists out the steps taken by the chip when going though a bonding process? I am trying to add as many RTT printouts as possible to know where...
finally I have done to implement that ADXL345 can throw data over BLE using nRF UART app service with this code . now my problem is how to change 2's complement ADXL345 data...
Hi,
We are using a nrf52832 in a serialized application with a STM32F4 and standard SPI as the transport layer. We are using the SDK V12 on the STM32 and softdevice S132...
Hello,
I want to add DFU fonction on my custom application. The final goal is to update my firmware from my custom app (not just once).
My setup is : SDK11 - nRF52832...
Hello All,
I am using the HRS example as reference from Nordic SDK14.1.
I have one central and 4 peripheral devices.
I have the MAC ID's for all the four peripherals...
Hello Nordic Experts,
I have One central device and and 4 peripheral devices.
At this point of time I am trying HRS example on it, the example is running fine with single...
Hi everyone,
We are trying to choose which protocol use for connecting devices based on Nordic SoCs.
We use devices in following way:
about 300 - 500 devices (wearable...
Hi there,
The dfu secure bootloader example is working fine with my nrf52832 sdk14.2 s132. but the experimental buttonless dfu in the example is not working for me. I was...
