Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Hi, As we know that, we can see, the data has been sent to nRF Cloud in JSON format by Thingy91-PCA20035. And we can also see that, we have respective APIs like "cloud_send...
Hey,
I am getting a
warning: #47-D: incompatible redefinition of macro "STATIC_ASSERT_SIMPLE" (declared at line 215) warning: #47-D: incompatible redefinition of macro...
Hello, I am working on a ble application which is streaming data via ble notifications. I am currently queuing up the packets in the notification queue and keeping track of...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
Hello, Nordic.
I'm currently developing multiple sensor beacons and a scanner for asset tracking (scanner app based on ble_app_uart_c)
ble_app_uart_c has SCAN...
Hello,
Im designing a board with nRF52832 with acceleration sensor and BLE application, so for the esd protection, should there be an housing of some sort, what all can...
We're migrating from Zentri AMS002 chip to to nRF52840.
We use custom service UUID: "175f8f23-a570-49bd-9627-815a6a27de2a" in nRF firmware.
As attached images show, custom...
Hi!
We're developing a board where we would like to switch between normal power mode (VDD shorted with VDDH) and high power mode (VDDH as input and VDD in highZ or supplying...
Hello everyone. I'm looking for BT5.1 most supported at current moment chip - to have devboard and SDK with ability of direction finding. Which one you can recommend? As I...
We are working with nRF52, in that we want to select any fix channel of BLE. We does not want to use ADH mechanism due to form a whole network on one channel.
So can you...
