Hi,
I am working on Temperature sensor MAX30208 using nrf52840 using zephyr. i am working on ncsv3.0.0 . I want to develop a driver for max30208 . can anyone guide me how...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Hi
I am currently working with my project with 52840 and i am using sdk v3.0.1 & toolchain v3.0.0 to develope.
I am learning how to use DFU over UART from the application...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
I am new to nRF51822 and seek expert's advice!
I am planning to prototype using nRF51822 Bluetooth Smart Beacon,
Can some one suggest if I can use nRF51822 Bluetooth...
Hello, when I check nRFgo SDK document and demo, find one difference, it's strange.
First, in demo, I check hal_nrf.c:
/**
Typedef for the RF_CH register. Contains...
It would be useful in debugging to be able to fire up gdb and point it at a single binary so that I can step through code in both the bootloader and the application. The mergehex...
I'm trying to figure out the RAM power and RAM retention on the nRF52. This is the micro I've used that has had the ability to turn chunks of RAM on or off.
Here's my understanding...
I'm trying to apply a firmware update using a zip file that has worked with older version of nRF Toolbox. Using the current version, (4.1.1) on iOS, I select DFU, then select...
Hi everybody.
I am opening a dedicate question after a recent topic that already helped me a lot, with another discussion pretty similar to my problem. Resuming briefly...
On the nrf52dk development kit, I want to power the target nrf52 from an external supply without powering the interface mcu (the debugging probe). How do I wire that? I don...
I'm trying to add nRF_Drivers files to Segger studio project, based on nrf51,51422(10028) examples. I added path in preprocessor user definitions and I added file like nrf_drv_lpcomp...
I set up my PWM Driver like this:
nrf_drv_pwm_config_t const nrf_drv_pwm_config =
{
.output_pins =
{
BSP_LED_2 | NRF_DRV_PWM_PIN_INVERTED, // channel 0
NRF_DRV_PWM_PIN_NOT_USED...
Hi,
I would like to test my C code with bootloader over air by BLE. I am using nrf51822 with soft device 110. Does Nordic Company is sharing any application which can bootload...
So this might be one of the most confusing issues i've come across sofar. We're currently developing a product based on NRF52 (more specifically NRF5283 QFAAB0) with a custom...
Is there firmware available as binary file that can be loaded to the nrf52832 that allows connectivity to is as a UART HCI compatible device?
Would the same firmware be...
Hi,
I am using "nRF Toolbox -> DFU" to change an application on my BLE module which contains; nRF52 device, SDK->v11.0.
I am using ".hex" file to load the application...
iphone5_b.psd m370_android6_b.psd long_write_error.png I using SDK11. I porting nus profile to my system and make a customer's UUID. I use Lightblue on iPhone 5 to connect...
