Hello team,
We have a problem here, we are running a new program with 5 years long-term standby IOT device, once we are trying to use SMS to configure the IOT device we...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
Hello, I have device with nrf51822-qfab and I need to run ble_app_template (use softdevice s110). What version of SoftDevice I must to use with SDK v6.1? About problem: It...
Hello, I find these structs:
ble_gatts_attr_md_t
ble_gatts_char_md_t
show up quite often in example projects. My qeustions are:
What are these? And when will I be...
I am using esb dpl in nrf5 sdk v11. I want to put a special packet in ack payload. but I think nrf_esb.c code can not do. the reason is that when on_radio_disabled_rx() is...
Hi,
I am developing a printed circuit board for myself using a NRF52 and I am unsure how to actually burn a bootloader program to the NRF52. Additionally, once the bootloader...
Hi All,
my device wakeup from system off casued from reset RWOFF, I read the register RESETSRC and byte E is 1.
maybe there is something about the configuration of gpio...
Hello,
I was reading about that 6LowPAN is being used in the IoT SDK.
I have a few questions about this.
Can the 6LoWPAN node communicate with another 6LoWPAN node...
Hi,
I am working nRF51822 communication. I am using nRF peripherals examples in SDK 11.0 series.
I would like to know the sleep mode examples in communication like after...
Hello,
I bought few nRF24L01+ modules and I integrated them in some custom PCBs that I designed.
I haven't been able to transmit information:
The TX FIFO is full...
I'm working on a very simple Gazell build - basically the gzll_ack_payload example with some of it pulled out, since I'm working on a board with no LEDs or buttons to run...
Hi,
I am trying to develop a PCB for the NRF52 that will use bluetooth capability. However, I was wondering if there were smaller antenna's that could be used rather than...
If I have Bluetooth earbuds, one set to master and the other a slave on my ears.
Is the communication between the ears, through the head, or around the head (Hair scalp...
Hi all
I have two questions/problems regarding the emulated System OFF mode with the NRF52832 and the SoftDevice S132 V2.0.1:
According to this thread , an infinite...
It is to my understanding that you DO have to worry about that when using keil download function or other means to program either the softdevice or your program to the nrf514xx...
hi,
I have created shared channel. currently I only have one master and one slave working.
Master is sending data to slave and it s working perfectly.
But I can not...
Hello,
i haven't found an answer to this question. Which address uses the PTX in Enhanced Shock Burst Protocol (nrf52832, SDK 11)? In the code I found only that:
NRF_RADIO...
