hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Anyone here have experience of going through FCC / CE certifications ?
We had a UK based company give us a rough cost but that quadrupled when they provided a final price...
Hello All,
Recently, I started working with nrf9160 and found it uses Zephyr for building application. Can anyone suggest me a any good tutorials for learning Zephyr from...
Hi I am following the instruction in the following link to do a open DFU through USB UART:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started...
We're experiencing occasional unexpected hardware watchdog resets. The watchdog is set to 10 minutes, and sometimes just 2 minutes after feeding the WDT we see a reset triggered...
Hi there,
I'm currently developing a ble mesh network for the Thingy 52. I'm accesing the temperature and humidity sensor but I need the firmware code of the Thingy 52...
Having problems bootloading my own application on my hardware. The application runs fine alone. Using SDK 16.0 and secure_bootloader/pca10056_uart example via Segger SES....
Hello,
anyone with with knowledge on how to control the gpio pins of the NRF 9160 SiP?
In my scenario, I am using P0.01 - P0.12 as digital control signals, for "Enableing...
Hi Nordic
For mesh-sdk-4.0 examples/light_switch/server, how many LPN can a server to establish friendship?
Is it limited to MESH_FRIEND_FRIENDSHIP_COUNT?
Regards...
Hi, I have custom nRF52832QFAAE1 when I tried to run Peripheral applications which are working fine. whereas BLE applications are not running it seems.
here are the things...
Hello,
When I clean a project and do a new build, parallel settings looks wring (my AMD ryzen 3900X with 12 cores never use more than 40 %).
Do someone have a setting...
Currently, we are testing the nRF52840 range evaluation using the nRF52840 EVK kit.
As of now, we are getting the only 120 to 125-meter range using 125kbps data rate @ 4dBM...
Hello.
I found in Provisioing chapter on this document: https://www.bluetooth.com/specifications/mesh-specifications/
something like list of provisioning commands: ...
Hello.
I plan to perform antenna matching to improve the performance of my design.
I would like to know any differences when performing the match on bare pcb and pcb...
Hi,
I'm working on a test for the pulse width measurement, the input is analog signal.
I'm using a while loop, and use nrfx_comp_sample in the loop to get the voltage...
