Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
Background:
I am using nRF52832 with SDK 15.3, SES v4.12. I want to perform OTA updates on the application i am building but i am having issues with it. I was using...
I'm not sure how often the Cortex-M4(F) design from ARM is updated, but what is version used in Nordic nRF52810/52832 devices? I want to know what ARM documentation version...
I can successfully download an image using nrfutil dfu serial when I use a test image (compiling the bootloader with the Nordic default public key) and the application starts...
Hi,
My requirement is to validate the PCA10040 dev board with a different set of UART pins. I have tried the following steps, but as soon as I start the firmware, it crashes...
Hello, I am new to BLE development and RF design. I've been doing as much reading as I can about RF design rules for PCB's, antenna performance, etc. Yet I am still uncertain...
I am trying to get a BMX160 working over SPI. I was following this post to make this code using the SPI example from the SDK as a basis. I am using SDK 15.3 with a nRF52840...
The app is foreground -> I am very easily connected with BLE device.
The app is in the background -> I get the callback and connect with the BLE device
The app is removed...
Hello.
I'm trying to get the example bootloader Segger project (secure_bootloader_ble_s132_pca10040) running on a custom board I have that uses the nRF52832 as its core...
I am working on nRF9160 and i found that when i change prj.conf, i need to rebuild code. if rebuild is not done(only build is done), changes made in prj.conf does not comes...
Hi
I'm currently evaluating the possibility of using nRF5340 in an upcoming project. As the chip is very new it's easy to understand that all specifications are not yet...
Hello, I am using nRF SDK for Mesh 3.1 and nRF52940 SoC. I have two nodes in my network which both act as a client and a server. Both of them subscribes and publishes to same...
Hi,
I am working with ANT bpwr tx profile and trying to implement HX711 and TWI sensor to it. TWI sensor is already working, but when I add library for HX711 from and start...
Hello,
It would be nice if the HVN tx complete event structure had the attribute handle of the characteristic that was just notified. This is already done for writes and...
Hey guys,
I'm working with the Laird DVK-BL652 and the Nordic SDK v.14.2.0 with Eclipse (Kepler) and try the example "SPI Master". I didn't modify this example but after...
Test Setup:
SD 6.1.0
SDK 15.2.0
Peripheral: nRF52840
Central: iOS 13.1
Central is connected to two peripherals, each peripheral is sending 50 pkt/s, each packet...
