Hi all,
I'm working with the nRF9160 DK and running the AWS IoT sample from the nRF Connect SDK v2.7.0 ( 5cb85570ca43 ). The device connects to the network and AWS IoT Core...
Hello forum ,
Here i tried to write and read from flash qspi w25q64 but read and write both are failed ..i m using nrf52840 kindly pls help me for read and write
Hello everybody,
now, I am solving problem with switching off Wi-Fi interface on nrf7002-DK. I am runnig SoftAP example on my nrf7002-DK board. So my board behaves like...
Hello everyone! I'm currently working on a custom PCB designed specifically for drone communication . In my design, I'm using the nRF52820 as the main microcontroller and...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi I'm currently develop new product based on RAK8212. I have problem with reprogramming devices. Programmer i use is nRF52-DK I'm not able to reprogram about 10% of devices...
Hello,
I have a low power application, which is activated by a push button press. (The DC-DC converter is also in shutdown mode normally, so the NRF9160 does not have power...
I am occasionally (very rarely) getting "Mesh assert at 0x00037996", but when I try to look this up, I get:
My understanding is that this means the mesh_assert is...
Hello, this is the nrf52833/52820 design drawn by the customer, because this is our first contact, please help to check whether it is reasonable? thank you.
Hello,
I'm working on a BLE app on an Arduino Nano 33 BLE, which is equiped with an nrf52840. I'm struggling to increase my BLE transfer speed ( i think due to the limitations...
Actually i was working on 3 boards, nRF51422,nRF51822 & nRF52840. While executing some examples on each board i realised that each board has its specific pca hex file to be...
I n the main of my program I have this( UBLOX_PWR_PIN = Pin16 of nrf ),
uart_init(); nrf_gpio_cfg_output(UBLOX_PWR_PIN); nrf_gpio_pin_set(UBLOX_PWR_PIN); nrf_delay_ms(200...
Hello,
I've a problem with a PPK board.
When the current go over 10mA the value reported is wrong, in my case should be 15mA and PPK measure 80mA and more. Instead, in...
Hello,
I am working on a project that is using nrf52840 chip as a peripheral and the product is supposed to last and run for 25 years. During that period the device will...
Hi everyone I have been reading the GPS data using nordic nrf52840 over the UART. I am able to receive as much as 64KB of data via the UART. Here's the scenario of whats been...
Hi All:
Applyed the under timeslot :
causes some peripherals(eg:static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(2)) n o access interrupt,
what 's the...
I am trying to get the maximum Tx power from the nRF5340 PDK.
The nRF5340 specifications say that setting VREGRADIO.VREQH is required to get the last +3dBm of transmit power...
Hi,
I know that this topic has been raised here many times, and I did read all of those threads, however none of them seem to solve my problem. As many others, what I am...
Hello,
I got my hand on the nRF9160 DK 0.9.0 and was able to connect it correctly to the nRF connect cloud.
I followed the nRF Connect for Cloud Certificate Update and...
Our repository is hosted at github and we are developing and building with Segger Embedded Studio.
Is there any documentation for setting up CI with github actions, travis...
