void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi I would like to interface the nrf9160 with amw136 (silicon labs) module wifi.
The amw136 has the interfaces: serial (UART, remote terminal), SoftAP and WLAN client (concurrent...
i am working on nrf52832 DK, i am trying to upgrade my development kit firmware using mobile
and i successfully build "secure_bootloader_ble_s132_pca10040.hex " application...
I'm currently using this setup on a fitness device prototype that will send battery status, scores and relevant infos. RPi >>>RFM69 915MHz )))))) ((((( RFM69 >>> Adafruit...
Hi,
I am using the softblink library in SDK 13.1 to control a RGB status indicator LED. It works fine, until I want to change the PWM settings or the LED pin.
The change...
I'm developing an interface I2C to one sensor including SCL, SDA and open-drain return to know if
the sensor is ready to work. After Reset by "Build and Run" form Segger...
Hi,
I'm a new guy for the development in nRF52840 and try to build the application by using 802.15.4. I have two questions, as follows:
Firstly, when I follow the instruction...
Hi, environment is nRF5_SDK_16.0.0_98a08e2 windows SES target is nrf52840. I am using the nordic dev board. The final product is a wearable, which will connect to a smartphone...
Hi All,
I'm using NRF52832 for our product. I test bootloader functionalities with development kit. The software system is also tested separately by directly programming...
Is it possible to achieve 2Mbps real speed when sending 2Mbs of data in BLE.50?
It supports USB 2.0 H / W, but the actual speed is full speed. Is high speed possible with...
What is the need for a provisioner? Is it mandatory to have provisioner while client and server communication? In which condition provisioner needed in mesh network? Which...
Hello,
This is more a question than a issue. I am working on a sample to transmit data from MOSI of the SPI to UDP. It is possible to see received data through SPI on LTE...
I would like to make a timer to check the GPIO status.
The current code is like below:
I already checked that timer function is worked by implant the specific event...
Hi, I am developing sensor reading via ble using nRF52 Development Kit from scratch.
Since bluetooth, nrf, sdk stuff are a whole new world for me, I m following step by...
Hello All,
Recently I got the nRF 52840 PDK kit and wanted to start with a simple example.
I tried do the following. It works but when I use the following it doesn't....
