I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi.
Using SDK13, nrf52, and the awful IDE Segger , I keep getting this error no matter what kind of code or project with PWM I use :
Undefined reference to nrf_drv_pwm_init...
Dear All,
I would like a simple way to read the voltage on one ADC pin without using any "adc_event_handler"-like solution.
I tried
reading=nrf_adc_convert_single(NRF_ADC_CONFIG_INPUT_2...
I'm trying to finish a handmade custom board I started. I had previous problems with the crystals, and a few others, but right the thing seems to be working ok. At least I...
NRF52832 on SDK 16.0.0, softdevice s132 (using SES) When writing constant value with FDS it saves normally, but when I try to write variable it saves some garbage. Here is...
Hi,
Is it possible to give 3.3V to the Vdd pin of my nrf52840 to change the reference voltage of saadc to 3.3V ? Do I have to change any configurations for the same?
Hello community
I want to advertise when physical pin 0.24 is high, and stop advertising when pin 0.24 is low. For this, I based my code on the Beacon Transmitter Sample...
Usually, I programmed the Thingy 91 with the nRF connect Programmer (right now version v.3.3.3). As my Thingy did not work with the asset tracker software and only with the...
Hi,
I am trying to integrate an UARTE application code with OpenThread example(thread_mqtt_sn_client_publisher_pca10056) on my nRF52840. My application code uses UARTE0...
Dear Sir/Madam,
I need help. I am using UART to send the data in the mesh topology .and I configured mesh using light_switch source code. is it enough to send data using...
I am trying to interpret the values in the INFO.VARIANT register for the nRF52840. The datasheet states "Build code (hardware version and production configuration). Encoded...
Hi,
After following the steps for building the documentation, I always get the following error:
"CMake Error at CMakeLists.txt:92 (add_subdirectory): add_subdirectory...
Dear All, I am trying to develop a simple BLE scanner that will scan for BLE beacons and print the retrieved packages. I am using nRF5 SDK v16.0.0. I have mostly succeeded...
I'm using an SES with NRF52840, w/ SDK 15.3, and SoftDevice S140. Im working on DFU and have two components:
- a main app that already takes care of moving a FW image into...
Hi
We are using %XMONITOR to get the network status and parameters, but we cannot understand some of its response:
1), sometimes, the PLMN may be "FFFFFF" and TAC may...
Hi!
I am in the process of trying to figure out how much it is actually going to cost for our devices to support LTE-M, and I have realized that I don't actually know what...
