Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
We are using a module which has nrf51822 on it. Before we have programmed it, we were able to see it when we scan for ble.
But after we program we could not able to detect...
I am building an automated test stand for programming our production devices. After programming, I need to pin-reset the device to leave debug mode so I can get an accurate...
We have an BLE application that we are targeting the nRF52 device for. The application demands using a UART interface to communicate to a host processor. In addition, we typically...
Hi all,
until now, I used nRF51 Chips on my board. I programed them trough the nRF51DK(PCA10028). But now I would like to work with nRF52832 Chip. I have a nRF52DK(PCA10040...
hi ..
i am new to mbed and nrf51.
softdevice is s130
if i enable the ADC in my project then other output(out3,4,5,6) is not working ok.
if ADC is not enabled then...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi
I have a problem when bootloading with nrf toolbox. It seems like when i flash files over 0x10000 in size the program overwrites itself. When i flash files with smaller...
I know this is somewhat "how long is a piece of string". I'm happy for guidance rather than solid numbers:
I'm trying to spec a "keep alive" circuit for an nRF51822 project...
In my S110 softdevice I want to accept connections only from centrals which passed OOB pairing.
My situation: There can be many centrals around my peripheral but only authorized...
We are trying to get an mBed-compiled hex file uploaded to production hardware but it is throwing the error "failed to read hex file".
The code is compiled for the nRF51...
Hello
I want to connect nRF51822 (on a readbearlab ble nano) to arduino micro which uses 5V logic on a 32U4 IC. I know I can use an external logic level shift, but I need...
In table 32 on page 25 of the NRF51 Reference Manual, there are a bunch of registers with the description "Reserved for Nordic firmware design" or "Reserved or Nordic hardware...
Dear nordic.
I am testing with nRF51822, and have some question about hardware stability check.
nRF51822 have Clock Monitor Unit (Clock fault detector)?
Is WDT same...
I am running a standard schedule loop where I wake-up, service any scheduled tasks, then immediately go back to sleep. However, I am observing the following pattern:
...
