Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
hi... I am working on nRF52832 . nRF52832 ,RX TX is connected to the esp8266 of tx,rx . i want to send the data from nRF52832 TO ESP8266 via uart . which function can i use...
I'm running the ble_peripheral\ble_app_uart example on my nrf52832, it works great.
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART" /**< Name...
Nordic Support,
I came across the following thread that says that SWO is not supported on the nRF9160:
https://devzone.nordicsemi.com/f/nordic-q-a/56098/is-swo-on-nrf9160...
https://devzone.nordicsemi.com/cfs-file/__key/communityserver-discussions-components-files/4/ADXL375_5F00_I2C.zip
i was using the code from above link
my sdk is 16
when...
Hi,
I am testing NFC on the nRF52840 preview kit that I have (PCA10056, v0.9.2) using the included NFC antenna. I am running the pre-compiled examples from the 16.0.0 SDK...
Hi
My company is currently using nrf52810 for a tracking application, but I see there're some new features on your nrf52811 iteration, as phased-array aperture and thread...
Hi!
I'd like to get a minimal "Hello World" example working for data transfer over 802.15.4
I have two of Makerdiary nRF52840 MDK USB Dongle, one as sender and one as...
Dear all,
I'm using nRF52810 with nRF5_SDK_16.0.0_98a08e2 and s112_nrf52_7.0.1_softdevice
I've implemented a custom service which exposes 4 characteristics.
2 of them...
Hi, I am trying to build ADXL362 with pca10090ns for nrf9160DK (PCA10090) (west build -b nrf9160_pca10090ns). I have added the following configurations in prj.conf. Though...
Hi teams,
During development, I need quite a long period timer for hours.
Searching for the subject, I found application timer can only handle few minutes because of 24bit...
I am evaluating the nRF52840-DK dev kit and want to to make changes to the 'LIGHT_SWITCH' application so I understand better how this is achieved. I have some demo code, but...
Hi
We are developing a custom board with nRF52840 and nRF9160. The 9160 is running a modified version of serial_LTE_modem, whereas the 52840 is running the main application...
On a custom pcb, an I2C sensor is connected on P0_15 and P0_16 ( SDA & SCL ).
When sensor reading is requested, the code is designed to wait till the reading is returned...
I am building an app that includes background DFU in the app. My app is based on the freertos example.
I am having problems during nrf_dfu_settings_write due to the checks...
Hi,
we are developing NB-IOT based GPS tracker based on nRF9160.
we have implemented the A-GPS based on SUPL. After using A-GPS there is a minor improvement in the overall...
