Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I use SDK16.
test fstorage write data.I find fstorage is busy appears when BLE sends and receives data.
for example main.c :
line 206: fst_erase_test(); line 207: NRF_LOG_INFO...
I am trying to implement the Simple On Off Server model in an existing project. In main.c I did the following:
1. In models_init_cb(), I added the following lines:
2...
Hello. I'm trying to make a product by running nrf51822 as an observer role.
This product will only use passive scanning and will not transmit any data.
How much energy...
Hello,
I have some issues sending valid information to nRF Connect app by bluetooth using the Aduino Nano 33 BLE with nRF52840 on it. I am using Arduino IDE and the ArduinoBLE...
Hi all,
The project I am working on consists of a BLE peripheral, a BLE central and an enhanced shockburst device. I run into a problem in the code of the peripheral:...
In a project based on Softdevice S132 7.0.1 employing the Softdevice timeslot API, I noticed that the nrf_radio_signal_callback_t function passed into sd_radio_session_open...
Hello,
I am using UART_1 to receive GNSS data. For UART_1, baud rate is 115200bps. On terminal, I can see the correct data when baud rate is set to 115200bps. When the baudrate...
Hi, i am using nrf52840 development kit , four servo motor . using 15.2 sdk version
here i am controlling the angle using adc values , i am done with one servo motor . pwm...
Hi
I am modifying the scanning and advertising paremeters for coded (125kbps).
I made the following changes in advertising
.primary_phy =BLE_GAP_PHY_CODED, instead of...
Hi All,
I am using nRF52832 SOC for my development. I would like to buy a packet sniffer for my BLE development.
Can someone please suggest a suitable device for this...
Hi
In the SDK, Replay_Cache_Entries is assigned a value of 40, which means that Replay_Cache can only process 40 unicast messages. That limits the maximum number of unicast...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
Device has both Central & peripheral functions.
It takes about...
Hi,
I used(SoftDevice 140, based on the ..RF5_SDK_15\examples\ble_peripheral\ble_app_beacon )
m_adv_params.properties.type = BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED;...
