Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi, I'm testing the MQTT implementation integrated in the NRF5 SDK.
This is my test environment: - A nRF52840 board with the MQTT publisher example from the SDK. - A Raspberry...
Hi,
We want to be able to upload a new firmware in my nrf52832 without serial connection.
I am trying to set up DFU over BLE and I stumbled upon few problems along the...
I'm porting an application from nRF52832, SDK 14.2.0, SD 5.0 to nRF52833.
I want to do this in two stages:
As quickly as possible validate our first prototype board...
Hi,
Using the RTC example in the 'nRF5 SDK 16 / examples / peripheral' as a starting point, we've programmed the rtc_handler to execute at regular intervals approx. every...
We are using libnrf_cc310_0.9.12.a. This doesn't work with position independent code check box in IAR (see Project Options->C/C++ Compiler->Code->Code and Read Only Data ...
Hi,
I'm trying to enable a HW timer (TIMER1) in my BLE application. I'm using SDK 16, and following the pattern shown in examples/peripherals/timer. However, when I get...
Hello
We have a project in which we need to be broadcasting data (around 30 bytes of message) to 150 unit via BLE.
we are thinking of using the nrf52832, which we...
Is it possible to read the value of APPROTECTSTATUS via the firmware? It seems like the AP register in not memory mapped, so maybe not. But maybe there is some kind of work...
Hi!
I'm trying to transfer data from UART to BLE in NRF52810. NRF52810 connects MSP430 controller via UART, MSP430 sends packet of 16 bytes lenght every 2ms (500 times in...
Hi,
I've seen this issue in other threads, but apparently all of them were solved on a private message basis.
So basically - my application for SUPL-C license keeps getting...
I am encountering an issue with PERSISTENT_STORAGE enabled. Currently I have a device set up to rapidly send out messages to test the sequence number updating and block allocation...
Hi Team,
We are using nrf9160 DK and we are new to begin this, We updated modem firmware using programmer, Now we would like to test the modem firmware.
So here are...
Hello,
This is first time to design the PCB antenna for nRF52840 BLE Chip. Can i use the nRF52840 DK Board HW layout for reference or should i use the USB dongle for nRF52840...
SDK16
S132
nrf52832
SES / Windows 10
After much searching this site and the web in general I'm reaching out for support.
While in low-power mode I'm seeing a pulse...
Hello im an Android developer and we have an app that uses an older library but still works with are older products.
we currently use
implementation 'no.nordicsemi.android...
