Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
I'm implementing a function which enters sleep mode and wakes up by interrupt like below..
Is this correct way to enter sleep mode? Do you know any other better ways...
Window10 nrf tag: 1.2.0 SES v4.4.2a
I'm attempting to code a one-shot mqtt function, but it fails in v1.2.0 whiile it succeeded in v1.1.0. I coded the below main.c by modifying...
Hello ,
I was working on BLE mesh implementation, It would be helpful if there is information regarding current consumption of different mesh nodes ( low power node, friend...
Dear team:
1.So how can I increase transmission withou improving TX power As for the transmission distance of nRF52832, apart from improving the TX power, what is the better...
Hello,
There is a particular task I'd like to accomplish, and I have been looking into the nRF52840 to do it. In a nutshell, I want to build a bi-directional relay for USB...
Hi,
i downloaded new SDK14 with example, after i upload hex from example in ble_peripheral/ble_app_hrs
I use s132 / nrf52
program stuck here :
ret_code_t nrf_sdh_enable_request...
Linker script `nrf_common.ld` in nRF5 SDK v16 defines __etext to point to the end of the .text section. It needs to be 4-byte aligned according to comments in `gcc_startup_xxxx...
Hello,
In order to try and implement passkeys, I've implemented my program inside of the glucose app example. The project compiles + runs and crashes sometimes randomly...
Hello everyone, just a quick question.
When routing on the nrf52832 WLCSP package, I noticed that the only inner pin "required" for use is the pin to enable DC/DC (Pin B6...
Hey guys,
I want to create an accurate timer without interrupts. My timer has to be very accurate because I have to send HIGH and LOW signals for 1us. I have read this pos...
Hello.
Currently I am trying to merge the peripheral example ble_uart and saadc examle. My little project is to send potentiometer values over ble.
As of now I have copied...
I have the bmdware.uvprojx project opened in Keil uVision 5 and have the BMD 350 breakout board containing the nRF52832 chip connected to my PC via a J Link debugger (EDU...
Hi all,
Here I am using the nrf52840 in my customized board, in parallel i have nrf52840 dev board.
I am using the twi peripheral to communicate with a i2c based sensor...
Hey,
I am using SDK16 and want to update the bootloader on my NRF52840 from SDK15 with a new one.
I modified the bootloader from SDK16 a little bit. Then I created a Zip...
To the kind attention of Nordic support team,
I have got in here two pictures of flash. The first one it is after installing bootloader and settings, softdevice and application...
