Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am working on a custom board with the nRF9160 SiP. It comes with pre-programmed modem firmware. Header pins for UART1 and UART2 are provided on the custom board. Is it possible...
This is a strange one. I had a custom PCB that included an MDBT42Q module. After I learned how to program it, it worked fine. I made a slight revision to the PCB, and this...
I'm implementing a function which enters sleep mode and wakes up by interrupt like below..
Is this correct way to enter sleep mode? Do you know any other better ways...
Window10 nrf tag: 1.2.0 SES v4.4.2a
I'm attempting to code a one-shot mqtt function, but it fails in v1.2.0 whiile it succeeded in v1.1.0. I coded the below main.c by modifying...
Hello ,
I was working on BLE mesh implementation, It would be helpful if there is information regarding current consumption of different mesh nodes ( low power node, friend...
Dear team:
1.So how can I increase transmission withou improving TX power As for the transmission distance of nRF52832, apart from improving the TX power, what is the better...
Hello,
There is a particular task I'd like to accomplish, and I have been looking into the nRF52840 to do it. In a nutshell, I want to build a bi-directional relay for USB...
Hi,
i downloaded new SDK14 with example, after i upload hex from example in ble_peripheral/ble_app_hrs
I use s132 / nrf52
program stuck here :
ret_code_t nrf_sdh_enable_request...
Linker script `nrf_common.ld` in nRF5 SDK v16 defines __etext to point to the end of the .text section. It needs to be 4-byte aligned according to comments in `gcc_startup_xxxx...
Hello,
In order to try and implement passkeys, I've implemented my program inside of the glucose app example. The project compiles + runs and crashes sometimes randomly...
Hello everyone, just a quick question.
When routing on the nrf52832 WLCSP package, I noticed that the only inner pin "required" for use is the pin to enable DC/DC (Pin B6...
Hey guys,
I want to create an accurate timer without interrupts. My timer has to be very accurate because I have to send HIGH and LOW signals for 1us. I have read this pos...
Hello.
Currently I am trying to merge the peripheral example ble_uart and saadc examle. My little project is to send potentiometer values over ble.
As of now I have copied...
I have the bmdware.uvprojx project opened in Keil uVision 5 and have the BMD 350 breakout board containing the nRF52832 chip connected to my PC via a J Link debugger (EDU...
Hi all,
Here I am using the nrf52840 in my customized board, in parallel i have nrf52840 dev board.
I am using the twi peripheral to communicate with a i2c based sensor...
