Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm using v1.2.0 for the nrf project and I am fairly confident I am using modem firmware 1.1.1 (though I don't know how to verify that).
I'm basing my project on "cloud_client...
Hi,
I am evaluating the ble_app_hrs_pca10056_s140 project with nRF5SDK160098a08e2 Dev kit and nRF82540 dev board.
I have put a breakpoint in line:
*p_erase_bonds = ...
Goodmorning,
what is the maxium current output for SPI pins on the nRF24LU1? The datasheet say "IVDD External load current" of 2mA, is this refered to the internal regulator...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
Hi all,
In our application we have a piconet master (acting as GATT client) and several piconet slaves (acting as GATT servers). We have only limited time on the channel...
Hello,
I've asked this question already at StackOverflow, and while I try Wireshark I wanted to see if someone has experienced the same issue and/or can provide further...
I can scan beacons with Scanner. and can use NUS (ble_periperall\ble_app_uart ) to get connect with device.
My goal is to combine both application Have NUS Service to connect...
As most developers using Nordic's SoftDevice quickly find out, halting the processor (e.g. hitting a break point) results in a fault and requires a reboot. This makes debugging...
we want to use nRF52833 as BLE5.1 AOA/DOA locator,here are some questions about to how to use it:
How many antennas are needed for direction finding/positioning? Is 6...
Hi everyone,
I have added the Characteristic User Description in order to add a human-readable name for my characteristics. However, the name still appears in hex format...
Hi everyone,
I have created a vendor service that works fine. Now I want to create a second one. What is the most efficient approach for doing this?
For the first service...
I am following the Zigbee Device Upgrade OTA tutorial and have run into an issue flashing the server firmware using a j-link and Particle Xenon dev board.
Environment Details...
Hi all,
I seem to be having a problem with running nRF connect for desktop 3.3.1 on MacOS (10.15.3). After installing the package to the application folder, on launching...
Hi,
When configuring a GPIO as output with DRIVE set to D0S1, i.e. "Disconnect '0' standard '1'", what is the leakage current when GPIO is set to 0, i.e Disconnected?
...
