Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello. Is it possible for a central device to retrieve the BDADDR( 6 byte array data ) of a past peripheral device by using the peer manager? ("past peripheral device" refers...
Does anyone know how the raw data message is structured to enable GATT Proxy? Here is a screenshot from the app. I know one byte is used to indicate whether to enable or disable...
Hi,
actually I developed a system based on an nRF24AP2 able to read data coming from different HRM ANT+ sensors and transmit them via WiFi using ESP8266 that is acting as...
I have clock drift issue, should I calibrate anything? I test this simple code to get 1second or 100ms signal both of them are inaccurate.
here is my code for 100ms; I tested...
I'm trying a new device based upon the nrf52810 and it won't run past sd_softdevice_enable - it goes to the assembler window and halts. The device does have a 32kHz xtal and...
Hello,
I was reading some SDK 15.3 code, there's something like this:
__STATIC_INLINE void pwr_mgmt_sleep_init(void) { #ifdef SOFTDEVICE_PRESENT ASSERT(current_int_priority_get...
Hi all, I'm developing nRF52840-DK to use it as an central device.
Base example is usbd_ble_uart: I'm going to communicate with peripheral device using BLE, and control...
We have a product that uses the nRF52840. We have seen that very rarely, unexpected resets happen with the reason being OFF. We have yet to encounter this issue in a lab setting...
I'm using the SPI manager to talk to an ILI9342 graphics IC. I need to toggle an IO line during a transaction or in between transfers. For the first byte the line will be...
I am trying to enable DFU over USB with the nRF52480, while keeping the possibility for Serial communication. I got a working example with both separate, however when I try...
It's my mistakes.
1.I want to measure temperature from DS18B20,but I don't confirm the capable of the pin - P0.05.Because it's Analog ，but DS18B20 is Digital.
2.I set the...
Hello, I'm getting started with a nRF52832, I've got the SDK 16.0 installed and what I think are all the latest packs installed. I try to build the examples\ble_peripheral...
Hello everyone.
I'm trying out the "Zigbee Multi Sensor Example". infocenter.nordicsemi.com/.../zigbee_multi_sensor_example.html
I have 2 nRF52840 devices.
I wrote the...
When my program starts, I set up a watchdog timer for 100 milliseconds and I start a repeated app timer that runs every 90 milliseconds to feed the watchdog. I use the app...
I'm trying to send data via UART from a NUCLEO-F401RE to the nRF 52840 DK. But the data I send is not comming through correctly. For example when I send 3 the nRF prints 32...
