Hello
I'm currently mounting a LittleFS partition in the internal flash of my Nordic MCU. However, since data is saved regularly to this partition, I’m concerned that the...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
I didn ' t use an external 32 . 768 crystal , the internal NRF_SDH_CLOCK_LF_SRC 0 I used。
NRF_SDH_CLOCK_LF_SRC 0
NRF_SDH_CLOCK_LF_RC_CTIV 16
NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hi! I’m currently implementing a hook using mcuboot_status_change() inside MCUboot. I’m following the path defined by CONFIG_MCUBOOT_ACTION_HOOKS , and I’ve confirmed that...
Hello,
I am trying to factory reset 2 nrf52840 dongles that I had very long ago with unknow applications on the dongles. When I erased and installed the image of nrf_desktop...
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
In this function in nrf_gpio.h, why is there a GPIO_PIN_CNF_INPUT_Connect value there?
Shouldn't that be GPIO_PIN_CNF_INPUT_Disconnect, or does it not really matter?
...
I need to pass a bit, to 500 recipients in a closed room.
My doubt is, 500 receptors works simultaneously without interference?
Ref. to buy:
www.ebay.com/.../251458486443...
I've seen various threads here with sample code attached that show how to set up a timer to measure a battery voltage periodically. They also seem to use an external crystal...
Dear Nordic Guy,I'm developing with nrf51822.
my costom code based on the hrs profile.and I modify the advertising timeout value to 30sec
and finally, I see the a few uA...
Hi,
I bought the nrf51822 chip itself, and created my own board. Now, can I still download the nRF51 SDK as per nAN-29?
I am stucked with the download page asking for...
Guys
I came over from the Arduino forums, I am searching for a new RF chip to use for a project i am working on but dont know which chip to pick. My application requires...
I want use uart to debug my ble program ,
In the devzone I found this and this to meet my need , but when I conditional compilation UART code into hex, I can not find my...
Hi All,
I am trying to use the HRM_RX sample code with my Linux PC side application. but i am not able to receive any UART RXD interrupt on nRf51422. I checked PC is sending...
We are developing a BTLE perihperal product using nRF51822 chip. But we would like our product can be up-gradable. So we will need a Bootloader (by UART or other interface...
while creating a Makefile for DFU, for BLE DualBank only, I'm getting some odd errors:
../bootloader_util_arm.c:19:1: error: 'at' attribute directive ignored [-Werror=attributes...
SDK v5.1 /v4.4.2
Keil 4.73/Keil 5.1
delay function seems doesn't work well in new version of keil. But I need it to bebug and flash nRF51822 with new keil.Need your help...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
This may be an obvious question, but I wanted to make sure that my assumptions are correct.
The nRF51822 is able to use an external 32kHz crystal oscillator for its low...
