Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Is the nRF24E1G obsolete?
If so, is there a drop-in replacement for the nRF24E1G.
We currently use the nRF24E1G in a product and have heard that it will no longer be produced...
Hi, I use IoT sdk with my iPhone to get current date and time, date comes in ble_cts_c_evt_t structure, how can I convert it to timestamp, I know that I have to subscribe...
Hello all,
As i want to lower the power consumption, may i know if its possible to connect the supply voltage of ntc thermistor to any gpio of nrf52832 instead of directly...
Hi,
I'm using the NRF52840 Preview DK and want to create my own BT stack with high throughput between NRF52 and other BT devices.
As base I'm using the ble_app_template...
Hi,
I followed the link, gnu-mcu-eclipse.github.io/.../ , to setup my debug environment before. I was able to view the registers. However, I updated my eclipse and the SVD...
I use the nRF52-SDK on an nRF52840 PDK, but if I start a scan request, I don't get the number of scanned channels back in the mlme_scan_conf_t.
I.e. mlme_scan_conf_t::unscanned_channels...
Hi! I need to understand the basic functionality of BLE Mesh.
Please see attached picture.
1. Is it true that a device (eg BLUE) through BLE mesh can communicate DATA...
Dear friends,
Software &Hardware: Power Profiling Application (a SDK example), S132 softdevice, nRF52832(PCA10040), Power Monitor. The measured average current consumptions...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
Hello. We are now starting our review to customize code for the pending use of the Nordic devices in low power mode. Have a mix of Nordic kits now. Using the nRF52832 (PCA10040...
Hi,
I am trying to implement buttonless DFU by following the ble_app_hrs example provided in the SDK and modifying the bootloader (nRF51_SDK_10.0.0\examples\ble_peripheral...
