Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
We have problem that after deleting bonding info on the NRF51822 the iOS APP doesn't know its bonding info have been removed and try-s to connect whitout asking for pairing...
Several different copies of the dev kit, and a couple of different hosts. I often get "Failed to secure connection. Disconnecting.". I can find where it's generated in the...
Hi Team
For security reasons, I would like the provisioner to stop further provisioning after the network is set up. SERVER_COUNT is usually not reached, since the number...
I am confused by the channel bits in register 0x05.
why is there a '1' in bit 1. I guess it can't be used and so the range is
00000010 - 2400MHz
00000011 - 2401MHz ...
Dear,
I am trying to test nRF52840 Preview DK.
Is there any method to test bluetooth 5.0 feature or spec?
Especially on speed and distance.
Thank you in advance!
Dear Madam/Sir,
I'm working with SDK14.2, softdevice5.0.0-2alpha, s140, and nRF52840 through the DevKit.
I'm recurring to the fstorage API to read/write/erase flash while...
Does enabling POFCON on nRF51822 lead to any increase in power consumption?
If yes then what is the value?
I struggle to find any information in Reference Manual or Product...
Hi
i am new with nr24L01 module , i am currently trying to configure them but , i am not able to read the RF_CH register just after write into it ? so i don't know if the...
Hello. I am using ble_app_uart from sdk14.2. I use pca100401, softdevice s132.
Advertising is generated using timer RTC. Board advertises and stops advertising without errors...
Here is our requirement.
We want to have four transmitters based on nRF2460 and more than 100 receivers. It means there will be four broadcasts.
Each receiver should...
Hi DevZone,
I am working on a project using nRF52840 preview DK and Arduino CAN Bus shield. I modified source code base on some Git Projects. It seems the SPI initialization...
Hi everyone!
I want to implement SPI with "ble_app_beacon" example with the following hw/sw.
DK : nrf52832
SDK : nRF5_SDK_14.2.0_17b948a
IDE : Segger Studio 3.34...
Recently,I use the SDK14 to develop the project,the initial project is in the content "SDK14/examples/peripheral/twi_scanner/pca10056",
Then and the spi example in the content...
