Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi, I'm a bit confused.... so far I was under the impression that SDK 12 was the last SDK that supported nRF51 development.
But now I found the section " Using the SDK...
I have a board with nrf51822 which is not equipped with HF crystal, but it has a LF one.
As pointed out in some other threads, calling HFCLKSTART on a board without functional...
Hello, I want to use the module app_mw_ble.c, but couldn't find its matching .h file, as a result, I got tons of "function declared implicitly" error.
For some reason,...
Good Day,
I am unable to connect my Rigado BMD-200 (NRF51822) to nRFgo studio using the J-Link EDU Mini. However, using the nRF connect application for Android I am able...
I need help configuring TIMER + DMA + PWM ( nrf52 ).
I would like to set the value of PWM with an interval of 100 ms and PWM configured to frequency of 20-40kHz.
Optinal...
I am using HRM demo application on nRF52840 DK with Samsung Tab-A. The nRF Connect App is running on the tablet. We are seeing that the dev kit gets disconnected soon after...
Hi,
The Bluetooth Developer Studio plugin fails to generate proper CP profile.
We use the last BDS version (1.1.3139) and the last version on the plugin (1.3)
Here...
Hi,
We are using nRF51822 Gazell protocol. We found that when host dbm is getting down to -61 or -62 dbm, the communication will lost. We had set it to +4db and use 250kb...
I have a question about how to build RSC (Running Speed & Cadence Service) ? especially using mbed compiler because I just found CSC (Cycling Speed & Cadence Service). like...
I am trying to add peer manager to multilink_central example on SDK14.1.0 based on the ble_app_hrs_c example. The code is running on nRF52832 and softdevice S132 5.0.
It...
hi,
I need combine to SAADC with BLE interface. The following is the code I have written. However, I'm unable to transmit information via bluetooth. Can anyone help me with...
Hi,
I have found this link devzone.nordicsemi.com/.../ . It seems you need to change SDK or softDevice to make it work with FreeRTOS. Could you please share more information...
Connecting to J-Link via USB...FAILED: Can not connect to J-Link via USB. I am using the BLE Sniffer 1.0 and when I star the Sniffer I get the error code that my software...
Hey guys,
I'm trying to make the FDS work with BLE and the scheduler.
But something doesn't right when I use the Softdevice and scheduler with the FDS.
Must I register...
