Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello Sir / Madam,
I want to load the BLE 5.0 (BLE Mesh) stack in nRF52832 chip.
Where I can find the latest Bluetooth 5.0 (BLE Mesh) stack on internet? Can you suggest...
Hi. My application uses an in-RAM log which I then read back to a terminal on the host using nrfjprog like this:
$/Users/eliot/dev/nRF5x_tools/nrfjprog/nrfjprog -c 1000...
Hello,
Exist an example of application ble_app_uart for pca20006?I found ble_app_uart for pca10028,but I want a project for pca20006(beacon) .I want use this project for...
Hello everyone!
I've tried to send something from mesh to computer in my LAN via UDP and it works fine. Now I'm trying to implement CoAP with acknowlegements. The problem...
hi
I am looking at ble dfu example. I have successfully tested on s132 and our board needs s332 and I want to test s332. However, I want to convert the app file to zip using...
I connected to nRF51422 and nRF52823 by mesh SDK.
now I want to connect with nRF51822.
is there mesh SDK for nRF51822?
if not, which code in nRF51422 should...
Hello everyone~
I need to use 2 UARTs to connect to different chips. If I use nRF82832, can I use 2 GPIO pins to simulate another UART? I just use it for one byte or two...
Does the nRF52810 have a wake on low power comparator from OFF mode?
This is a feature that exists on nRF51822, but I cannot seem to see it in the nRF52810 as a feature...
Often, I create and download Macros and the 'play' icon is in the lead-line of the macro but after import to nRF Connect, the macro cannot be played and is NOT blue but rather...
Hello,
I am using sdk12.2 and nrf52. I want to send more than 8 packets of data to nrf app. How can I do that?
My code snippet is as follows:
enter code here
void...
Log-2018-01-12-11-49.txt When I use the nrf connect app to connect my device, it often does not connect to my device.And i see the error on the log is： ERROR 22 GATT_CONN_TERMINATE_LOCAL_HOST...
I have learned that the "sd_power_dcdc_mode_set ()" function does the appropriate mode switch.(LDO and DCDC)
I learned from the following URL.
devzone.nordicsemi.com...
Hi to everyone!
It's the first time I use and program clocks in a device. I'm very lost with crystals, power management and this stuff.
I have a custom board with two...
I am trying to flash custom firmware to Thingy using nrf52dk and nrfgostudio.
I have attached a cable from the debug out port on the DK to Thingy, and followed the steps...
