I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
My project cannot be debugged using Segger Embedded Studio. The debugger doesn't halt at the application main and instead keeps running. Hitting a pause shows the debugger...
Dear all，
We use thingy's microphone collect data and transmit to Android mobile by BLE, and need no loss of reliable data transmission.
How to do?
Thanks a lot.
I have developed custom PCB with nRF52832. My antenna layout is very similar to layout present on nRF52DK (PCA10040). All works well. Now, in next prototype, I want to add...
I designed the NRF8001 into my circuit board and my application processor is connected to it. Now I need to develop my application program such that I can transmit and receive...
Hi,
I am working with the Red Bear BLE Nano 2 (nrf52832) and programming it in Arduino IDE .
I am trying to merge the BLE_HRM example with a TWI example to be able to...
Hey,
I have a problem with receiving data on my Android app.
I'm sending several data via Services & Notfication Characteristics from my NRF52840 Application to my Android...
hi,
I have some problems about pwm register.
1.NRF_PWM0->MODE
2.NRF_PWM0->COUNTERTOP
3.NRF_PWM0->LOOP
4.NRF_PWM0->DECODER
5.NRF_PWM0->SEQ[0].PTR
6.NRF_PWM0-...
I use rRF52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command Line Tools (nrfjprog...
I'm trying to port the _12.3.0_ DFU bootloader_secure example to my custom nrf51822 board.
The example can run perfectly on pca10028 board, but not on my 51822 board even...
Hi All,
I am developing an application on nRF52840 Preview DK which does not need the Soft device. But it needs the MBR to run a bootloader for Firmware update purpose....
Hi,
Now I am using nRF52382 to make a product which needs a accurate one second timing. Then I use the project "nRF5_SDK_15.0.0_a53641a\examples\peripheral\rtc" and "nRF5_SDK_15...
Hi there!
Device: nRF52 DK
App: nRF connect
Compiler/IDE: Segger Embedded studio
SDK version: 14.2
Soft device: s132
Problem description: I am trying to run blood...
Hi,
I am reading a BMX055 via I2C which consists of three sensors with three addresses.
I got the easyDMA running to read 10 times the gyro using the PPI and the data...
Hello,
my first question is about TX carrier frequency accuracy measurement. The equation given in the whtie papers is
(|f_measured - f_programmed|) / f_programmed <=...
