Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
We are developing a product based on ble mesh. We are planning to select NRF52832 chip. Currently what is status of ble mesh on this chip. Does nRF open-mesh support this...
Hi everyone,
I am using new mesh released sdk v2.0.0 in that i have successfully run light switch demo using 3 nRF52832 baord. One for provisioner, 2 client, 3- server....
Hello:
From the nrf52832 data sheet can be seen in the crystal pin is the internal input capacitance, in the table (19.4.2 64 MHz crystal oscillator (HFXO))on P109 , has...
Hi,
I am working with the HID keyboard example in the pca10028 development kit and I facing following problem.
I can connect, pair and bod with Android and IOS devices...
Hi,
I'm testing a PCA10056 S140 (nrF 52840 PDK), SDK15.
I want to test long range extension : using ble_app_att_mtu_throughput application sample.
But when I change...
Hey, I see that the nrf52840 has a single i2s peripheral. and the max sample witdh supported is 24bits. Is there any way to get 4 channel 16bit audio? I only need to record...
Hello Team,
We are using nrf52832 device and SDK version 12.2 Softdevice3.1 to program our watch device.
We have iOS & Android native application to communicate and...
Hi,
I'm trying to transmit data at about 500kbps from custom nRF52 board (peripheral, s132 v5, SDK14.0) to a PCA10040 board with a connectivity FW (based on v3.0.1) connected...
hi to all,
i am developing a device with nrf51822 and i have Inadequate ram problem, i know that softdevice required ram determined in runtime, so there is any way to know...
Hi to all,
i am developing a device with NRF51822 SOC, i want implement a peripheral device and deploy in it a service with two characteristic with notify property, i know...
I want to test the demo https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo that requires Mesh 1.0.1, but I do not seem to find it anywhere. Can someone point me...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...