Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hi,
I'm resetting the chip externally using the reset pin to not be in debug mode. I'm running the system off example here modified to not use buttons.
I have the J...
Hi,
I am looking for some assistance to choose the best way using the nrf52832 processor in a correct way.
The main task is to generate a 1KHz PWM Signal with changeable...
Hello,
I am using nrf51822 ceaa package.
What would happen if dec1 pin is not connected to a capacitor?
According to the datasheet, it is for power decoupling and...
I'm developing py script for automation testing of nRF devices.
My script is based Nordic's scripts Master Control Panel\3.7.1.8567\lib\dfu...
So, during testing my script...
Hello,
I have some devices based on NRF51822 using ESB lib and developed with Nrf51 SDK v10 (no softdevice). Since Nrf5 SDK v11 is released, the new device will be developed...
Hi,
I am curious about how the connection is keep while using the 32.768K in BLE link layer in power saving mode.
I know that the connection interval is based on multiple...
Hi,
I have two BLE centrals and one BLE peripheral. Both centrals are in range of the peripheral and both want to connect to the peripheral at exactly same time. What central...
Hello ,
We are working to an OEM Security System project that is using BLE.
The system contains at least 2 modules that communicate using the BLE technology.
One of...
I am trying to run the example ble_app_hrs on the nRF51 dk PCA10028. I target and build the file, and I believe it makes it onto the device, as the old program on the device...
Hi,
when i program my eval kit using nRFgo studio, the chip dosen't work unless i do a hard reset OR put off supply and put on again.
Any idea ? My program, is dfu bootloader...
Hello Nordic Team,
I am sorry to say this, our development team found a major glitch in micro-esb communication protocol. we are in stage of pre-production of medical sensors...
Hi
We are thinking of using NRF51 for BLE and CPU capabilities. But we also need a Wifi add-on to connect to cloud.
What is the right chipset for this? Which ones are...
I have a demo(s110) set up with some custom services, and in them custom characteristics. The services each relate to a specific sensor element on my device, so have a mostly...
I'm using ble_nus_string_send() to send 15 bytes over BLE UART.
As expected it sends 15 bytes, however on occasion 14 bytes are sent instead of 15 bytes.
Would there...
I ordered nrf8002 IC. I am using following breakout board PCB & not using Nordic development kit.
www.proto-advantage.com/.../product_info.php
I gave 3.3V to both VDD...
