I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
These posts indicate there was a problem at least at one point with the S132 SoftDevice erroneously requiring FPU:
https://devzone.nordicsemi.com/f/nordic-q-a/8133/nrf52...
On line 301 of app_timer.c there is the following code:
// No more timers in the list. Reset RTC1 in case Start timer operations are present in the queue.
if (mp_timer_id_head...
Hello,
I completely don't understand how to increase the packet size in the ble_uart example (using SDK 14.2 in both sides)!
I have two NRF52 DK boards and nothing is...
Hi all,
I'd like to design using 2ch SPI of nRF52832(as a MCU).
So, How many SPI channels of nRF52832?
And, Inform me pins of SPI port of nRF52832.
Best Regards...
Hi
I am creating bond from the Nordic device to my Android APP.
But I want to change the name of the device immediately after the bond has been created.
i.e from NEWDEVICE...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hi,
Just a quick question about how the ble_app_uart works.
When sending to the UART from "static void nus_data_handler(ble_nus_evt_t * p_evt)" and also receiving from...
Interrupt or main() context, or something else?
We're using S140 SoftDevice, nRF52840 and Segger Embedded Studio 3.30
We're also usinq Quantum Leaps ( https://www.state...
Hi
I am use hids, ancs and hrs services together with bonding. Phone should hold the connection with device. I am enable heart rate sensor when notification is enabled ...
Hello,
Trying to make GATT services configuration for nRF8001 chip in nRFgo studio. On services.h file generation I see Generation of source files failed window with "Generate...
Hi, Nordic team:
Now, I'm using NRF51822QFAC in a production with the SDK 10.0, the firmware includes FreeRTOS and DFU, when start the DFU in nRF-Connect APP, it can't jump...
All standard SDK examples disconnect immediately once I try to connect to from Android device. But when I flash the same sketch to nRF52-DK, I can connect successfully.
...