Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi Nordic,
Running a gdb session on nRF51, it is difficult to debug the code beyond the SoftDevice initialization. Then, I have to step through with (gdb)ni, but this is...
Hello everybody,
I used to my PCA10028 DK board with nRF51-DK-mbed-IF but I wanted to revert for nRF51-DK-J-Link-IF. According to the nRF51-DK - User Guide v1_0 documentation...
I have the code below initializing TIMER1 and and IRQ every 1ms. I call app_sched_event_put within the timer and I get a Hardfault.
Any hints on what is going on ?
Thanks...
I just bought a nRF5-DK and I couldn't get it to work flashing other nrf51822s. The modules I'm using are these wireless-tag.com/.../nrf51822-02.aspx
Here's literally what...
I have a PCA10001 setup and I am using SDK v9. I have opened the UART example in CrossStudio.
It compiles/builds and I am debugging with breakpoints.
My question is...
Hello,
I use the interface I2C to communicate to the Light Sensor, and also use a timer to read the value back every 1 sec now.
I'm wondering that can I use the interface...
I use nrf51822 by example ble_peripheral/ble_app_uart with with SoftDevice 8.1.0, at the same time, I use pwm driver library, But it does not work well, What I need to do...
Hello,
I have a problem with db_discovery_event_handler execution when having multiple S110 peripherials present when turning S120 central on. I have two different types...
I am seeing three things I don't understand in a modified ble_app_rscs codebase. I'm hopeful that someone else can recognize my symptoms and tell me what I'm doing wrong....
I've got a project that works perfectly on the PCA10028 DK. But the behavior is quite different when downloaded to my nRF51822 production target. My target is connected to...
Hi
I use nRF51822 of Gazell mode and RXF2401C(PA)
PA's TXEN has been pulled, what RXEX in there enbale and disable it?
(Host and Device must be)
Thank you!
Hi everyone,
My question is how much current it´s capable to sink an I/O pin configured as output ´0´ ?
In my case I have to discharge a capacitor throught an output...
I am using sd_power_system_off() to enter System Off. It is my understanding that all peripherals are off in System Off, but that GPIO configuration is retained. I have a...
I have the following code
// Initialize timer module, making it use the scheduler
APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS, APP_TIMER_OP_QUEUE_SIZE...
