I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
SDK13, S132, nRF52832.
I use whitelist and bond peripherails. But after bonded 20 pcs of peripherials, I can work with only first 8 bonded.
Which parameters should change...
I’m trying to create a nRF8001 device without the need for any keys, because the device will be inaccessible in mounted condition. Additionally the connection must be secured...
I am utilizing the nRF52832 with softdevice S332 with both ANT and BLE enabled (no peer manager). When I set the ANT search for a channel to use ANT_WAVEFORM_FAST it causes...
Hi,
I am trying to use fds file system to save some data in flash,
when using the example code of sdk 14.0.1, it is not normally operated,
NRF_ERROR_INVALID_PARAM error...
Hello
I am using nRF51822 Nordic controller, SDK 9 and S130 Soft-Device.
I have used to generate a 1 KHz PWM signal successfully using timer 1.
And generating a 4 MHz...
Hi,
I have designed one custom board using nrf52810 and GPS module. where i can get the gps data via UART to my nrf52810 chip and then from nrf52810 sending same data to...
Hello Sir,
we have designed custom PCB using nRF52832, I am little confused for is it OK. I have attached top and bottom layer layout of my PCB please sir review it and...
Hi guys,
I'm struggling over some basic concepts related to the Mesh SDK, specifically with the Bearer layer and why the Mesh SDK uses the Timeslot API. I'll try to explain...
Hi all,
I'm trying to writing a device information service client on top of ble_app_multilink_central example on nRF52830 using SDK14.1.0 and softdevice 5.0 and have a...
Hello World,
I checked the Developers Zone, but I have not found the direct example of my problem.
I use the RuuviTag board with NRF52832_XXAA.
I use it as a development...
Hello,
I have question about signal names in datasheet nRF52840.
On the pins B19 and T2 on page 14 both pins have the same initial signal names (P0.11).
Please send me...
Hello,
I would like to add the ST7735 driver from the nRF5_SDK to the Mesh SDK along with the necessary components (SPI,..). I copied the entire components directory to...
How is the health model supposed to work?
I'm currently doing some tests with the light switch example and I don't really understand the different roles of the nodes in the...
Hello,
I have some trouble to write/read data in flash region,
I am using FICR region to save data,
if trying the command : nrfjprog --memrd 0x10000010 --n 0x10
I...
Hello All
I am using an SOC which has nrf51822. I am trying the blinky example with the softdevice. When I debug the code, the code first enters the SystemInit function...
