I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello.
Until now, we work with NRF52832 for a new product but we have identified that the memory (64kB of RAM and 512kB of flash) of the chip will not sufficient for our...
Maximum connection node in 6lowpan over BLE
I am testing Pi to Nordic node (NRF52832 IoT Softdevice). When I test connection, maximum connection node is 10. Do you know...
Dear all,
Sorry for asking an old question but I can't find any similar situation in the forum. I now have 3 boards: 1 is 52810 EVB, 1 is 52810 QFAA ( 48 pins) custom made...
I bougth pca10056 and I need use it with Keil, but I do not find the pack installer for this board on "Pack Installer".
Furthermore, keil does not recognize my board.
...
I am using a lithium polymer 4.2V battery to power an nRF51822 (as a side note the power goes through a voltage regulator before going to Vdd). I want to be able to check...
When calling app_sched_event_put() no check is done whether the exact same record (same data, length and function pointer) already exists in the queue. We have setup where...
Hello,
I've tried to implement a custom service with a custom chacteristic, that shows the values per notification in the MCP (Master Control Panel) in percentage.
I played...
Hi,
I am using NRF24L01 module and I would like to transmit I2S signal through this module. I used SGTL 5000 audio shield for converting audio signal from microphone to...
Hi,
I'd like to determine the cause of a watchdog reset. I was hoping to utilize the WDT event handler (passed in to nrf_drv_wdt_init() ) to record the PC of the application...
I am trying to get the S132 Central Multilink example to run with 20 peripherals instead of 8. So far, I have made the following modifications:
In sdk_config:
Increased...
I wonder about the accuracy specifications in chapter 9 of the ppk user guide. It says +-20% of readout on average value. Is this only the calculated average of the python...
Using S130 to request notifications of radio activity as:
fails with NRF_ERROR_INVALID_PARAM.
Is there a reason this combination is disallowed? The use case for it is...
I would like to add the UART part to my application. But I will get these errors:
..........\components\libraries\uart\app_uart_fifo.c(109): error: #20: identifier "UART0_CONFIG_PSEL_TXD...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...